Index Catalog // ScholarsArchive@OSU

A numerical study of the response of Lake Kinneret to wind forcing

Creator:: Vernieres, Guillaume
Abstract:: Lake Kinneret is Israel's only fresh water lake (unless you count the Dead Sea). It spans roughly 20km from north to south, and about 12km at its widest east west extent. It is not quite 50m deep at its deepest point. In late spring, the lake stratifies significantly and remains...
Resource Type:: Masters Thesis
Full Text:: Mechanical Engineering presented on April 3, 2000. Title: A Numerical Study of the Response of Lake

Effects of orifice geometry and surface boundary condition on heat transfer of impinging jet array

Creator:: Kanokjaruvijit, Koonlaya.
Abstract:: The effects of the orifice geometry and the surface boundary condition on the heat transfer distribution to a flat surface of an impinging jet array were investigated. The jet array impinged normally onto the surface which was either isothermal or had a uniform heat flux. The experiments were performed for...
Resource Type:: Masters Thesis
Full Text:: @ for the degree of Master of Science in Mechanical Engineering presented on February 16, 2000. Title

Flow characteristics of semi-confined impinging jet arrays

Creator:: Dano, Bertrand P. E.
Abstract:: The present study proposes to investigate the flow structure of different arrays of jets impinging on a flat surface enclosed by three walls, creating a channel that forces the air to leave in one preferential direction, generating a self sustain crossflow. Details of both the mean and some turbulence quantities...
Resource Type:: Masters Thesis
Full Text:: Engineering presented on October 12, 2000. Title: Flow Characteristics of Semi-confined Impinging Jet Arrays

Diagnostic analysis for mechanical systems

Creator:: Henning, Scott A.
Abstract:: An analysis and modeling method of the diagnostic characteristics of a mechanical or electromechanical system is presented. Diagnosability analysis is especially relevant given the complexities and functional interdependencies of modern-day systems, since improvements in diagnosability can lead to a reduction of a system's life-cycle costs. The diagnosis process of a...
Resource Type:: Masters Thesis
Full Text:: of the requirements for the degree of Master of Science Presented January 21, 2000

An experimental study of fluid flow and heat transfer in rectangular microchannels

Creator:: Popescu, Aristotel
Resource Type:: Dissertation
Full Text:: Philosophy in Mechanical Engineering presented on November 30, 2000. Title : An Experimental Study of Fluid

Laminar natural convection within long vertical uniformly heated parallel-plate channels and circular tubes

Creator:: Vorayos, Nat
Abstract:: The problem of simple mathematical models of laminar natural convective flow within a long vertical parallel-plate channels and circular tubes kept at uniformly heated walls is revisited to seek a clear physical understanding of heat transfer mechanisms. A series solution method to analyze the fully developed flow and an integral...
Resource Type:: Dissertation
Full Text:: degree of Doctor of Philosophy in Mechanical Engineering presented on June 27. 2000. Title: Laminar

A product development process measurement methodology applied to small manufacturing companies

Creator:: Schlegel, Stephen C.
Abstract:: The implementation of concurrent engineering into many large companies has greatly improved their product development processes. These companies have seen significant gains in quality and customer satisfaction with reduced product costs, defects, and time-to-market (Lake, 1992). Many large companies have successfully employed this relatively new product development philosophy. However, smaller...
Resource Type:: Masters Thesis
Full Text:: degree of Master of Science in Mechanical Engineering presented on May 26, 2000. Title: A Product

Properties of veneer sliced from serpentine-end-matched flitches

Creator:: Liu, Yuqing
Abstract:: Eighteen Ponderosa Pine (Pinus ponderosa Dougl.ex.laws) veneer flitches were randomly selected and crosscut into paired flitches. Serpentine-end-matched (SEM) joints were machined in the flitches, joint amplitude equal to the width in one half of the paired flitch and joint amplitude equal to 2/3 width in the other half of the...
Resource Type:: Masters Thesis

Electric Actuation of the Main Flight Valves of a Small Bi-Propellant Liquid Engine

Creator:: Edgerton, Jacob M.
Abstract:: The High Altitude Liquid Engine (HALE) team is developing of a 2000 lbf thrust liquid propellant engine for a flight vehicle capable of breaching the Karman Line (100 km in altitude). As part the development of this flight vehicle, this research focuses on the design and characterization of a novel...
Resource Type:: Honors College Thesis
Full Text:: (HALE) team is developing of a 2000 lbf thrust liquid propellant engine for a flight vehicle capable of

Turbulent Heat Transfer of Supercritical Carbon Dioxide in the Proximity of the Pseudo-Critical Point with Non-Uniform Heat Flux Boundary Conditions

Creator:: Jajja, Saad A.
Abstract:: Seven decades of supercritical heat transfer research have not seen an attempt to characterize turbulent thermal transport in internal flows subject to asymmetric heating. Existing heat transfer models therefore do not account for phenomena that dictates thermal transport, in the proximity of the pseudo-critical point, for non-uniform heating. Additionally, past...
Resource Type:: Dissertation
Full Text:: (5 ≤ q′′ ≤ 50 W cm-2), mass flux (315 ≤ G ≤ 2000 kg m-2 s-1), and reduced pressure (1.03 ≤ PR ≤ 1.1

ScholarsArchive@OSU

A numerical study of the response of Lake Kinneret to wind forcing

Effects of orifice geometry and surface boundary condition on heat transfer of impinging jet array

Flow characteristics of semi-confined impinging jet arrays

Diagnostic analysis for mechanical systems

An experimental study of fluid flow and heat transfer in rectangular microchannels

Laminar natural convection within long vertical uniformly heated parallel-plate channels and circular tubes

A product development process measurement methodology applied to small manufacturing companies

Properties of veneer sliced from serpentine-end-matched flitches

Electric Actuation of the Main Flight Valves of a Small Bi-Propellant Liquid Engine

Turbulent Heat Transfer of Supercritical Carbon Dioxide in the Proximity of the Pseudo-Critical Point with Non-Uniform Heat Flux Boundary Conditions

Limit your search

Academic Affiliation

Advisor

Commencement Year

Committee Member

Conference Name

Creator

Contributor

Date

Decade

Degree Field

Degree Level

Degree Name

File Format

Language

License

Location

Non-Academic Affiliation

Peer Reviewed

Resource Type

Rights Statement

Subject

Search Constraints

Search Results

Limit your search