Many publications, documents, codes and guidelines exist related to the seismic evaluation and rehabilitation design of existing buildings. This report discusses the assumptions and methods employed for investigation of two wood structures using four references: FEMA 154, FEMA 356, ASCEI per SEI 31, and 1997 UBC. The screening performed using...
The objectives of this study were to evaluate the performance of wood-frame shear walls under monotonic, cyclic, and earthquake loads by: 1) comparing performance under each loading protocol; 2) evaluating effects of anchorage; and 3) eval-uating performance qualitatively and quantitatively with respect to code-defined performance measures. Tests were conducted on...
The forces exerted on light-frame wood buildings as a result of surge and waves are not fully understood. With a better understanding of these types of forces, it may eventually be possible to build coastal structures to better withstand the loads. In this paper, a recent two part experimental study...
Presently, the production of wood composites relies on the formaldehyde-based wood adhesives such as phenol-formaldehyde (PF) and urea-formaldehyde (UF). However, their dependence on exhaustible fossil fuels and the emission of carcinogenic formaldehyde prompt to develop an environmentally friendly adhesive from renewable natural resources. This work focuses on development and characterization...
Sawmills are very complex systems that involve many manufacturing processes. The variability of their raw material adds further to this complexity as each log has characteristics that determine its processing path. Therefore, computer simulation is a very useful technique for analyzing sawmill performance. This thesis describes a simulation computer model...
A sawmill is similar to other manufacturing enterprises when it comes to making decisions, scheduling production and meeting customer demands. In order to help sawmills achieve their goals, and because there is such a high degree of variability in the raw material used in this industry, computer simulation has proven...
Wood-plastic composites (WPCs) are one of the fastest-growing sectors of the
wood composites industry. However, the strengths of WPCs are typically low
because of the poor interfacial adhesion between hydrophilic wood and
hydrophobic thermoplastics. A compatibilizer that can form bridges between wood
and plastics is required to give WPCs desirable...
Heartwood can have properties that are distinct from sapwood,
including resistance to insect and microbial attack. Despite the practical
importance of heartwood formation in trees, a review of the literature revealed
that little was known about the effects of environmental factors on heartwood
quality or how variations in heartwood properties...
The emission of organic compounds from wood manufacturing
facilities is an important regulatory concern due to their effects on ambient
air quality. Control technologies, such as oxidizers and biofiltration, are
used to remove organics from air streams; however, most removal
technologies have high costs or cause additional negative environmental
impact....
The dynamics of radio frequency (RF) laminated veneer lumber (LVL) pressing are explored for the purpose of optimizing this process. The RF LVL press at the Albany Trus Joist plant is the focus of this investigation. The investigation first focuses on bond strength development characteristics of the Georgia Pacific adhesive...
The goal of this study was to optimize a through-boring pattern that will provide adequate preservative penetration while minimizing the reduction in overall pole bending strength. Hole spacing was developed using longitudinal and transverse chemical penetration data from previous studies. Finite element analysis was used as a preliminary assessment tool...
In wood-plastic composites (WPCs) a compatibilizer is often used to improve
the interfacial adhesion between the hydrophilic wood filler and the hydrophobic
plastic matrix. At present, while the basic concepts of compatibilization are
understood, the optimized chemical structures of an effective compatibilizer, including
the ideal structures of the wood-binding domain...
Key parts of the lateral force resisting system in wood-frame buildings
are the shearwafls and the connections. The connections in wooden buildings
are the primary source of ductility and energy dissipation; these are essential
properties when buildings are exposed to lateral forces, such as wind and
earthquakes. Shearwall design is...
This study examined the relationship of interfacial shear strength (IFSS) and
bending strength (MOR) of several different wood-plastic composites (WPC's).
Plastics utilized were high-density polyethylene (HDPE) and polypropylene (PP).
Pine and oak were used as the wood species. Compatibilizers used included maleicanhydride
polyethylene (MAPE), polymeric methylene diphenyl diisocyanate (PMDI),
KymeneTM,...
The objectives of this study were to evaluate the performance of wood frame shear walls
under monotonic, cyclic and earthquake loads by: (1) estimating the variability of shear wall
performance, (2) comparing the performance of walls under each loading protocol, (3) evaluating
the effects of anchorage on wall performance, and...
Natural fibers such as wood, flax, and hemp are frequently used as fillers in natural fiber-plastic composites (NFPCs). At present, wood fiber is the most commonly used filler in the production of wood-plastic composites (WPCs). The advantages of these fibers compared to conventional inorganic fibers such as glass fiber is...
The overall goal of this study is to evaluate the earthquake performance of wood frame
shear walls, and more specifically: (1) to compare the performance differences of fully and
partially anchored walls under monotonic, cyclic, and earthquake loads, (2) to compare wall
performance under earthquake loads with that of standardized...
The goal of this project was to develop an integrated pest management strategy
for the control of a powder-post beetle (Dinoderus minutus F.). This species causes
serious damage in Philippine bamboo. Developmental threshold and thermal constants
were examined and natural enemies and ftmgi associated with beetles were investigated.
Finally, the...
Innovation is considered the ultimate drive for business success. Fast growing furniture imports from China have become a controversial topic within U.S. wood and furniture industries. Low-cost production, which is stereotypically considered as the major competitive advantage of the Chinese-made products, has received considerable attention by a large body of...
In investigating wood treatment as a possible processing option for Alaska forest products manufacturers, the double-diffusion method using sodium fluoride followed by a copper sulfate appeared to be the most advantageous approach. Yet, little information was available as to the chemical retention after treating and its resistance to leaching. Green...
Supercritical fluid (SCF) impregnation is a promising preservative treatment method, however, the development of SCF processes has been slowed by a limited understanding of the process. Developing a better understanding of the effects of various process parameters on treatment results would allow for a more rational development of SCF impregnation....
This study examined the decay resistance of the pine and maple components of wood plastic composites (WPC' s) of varying thicknesses exposed on several culture media to wood decay fungi under laboratory conditions. The ability of malt agar extract (MEA), potato dextrose agar (PDA), amended basal salts, sawdust (maple and...
Softwood plywood is one of the structural wood products studied in the CORRIM
II effort to document the environmental performance of wood product in residential
structures. Life-cycle inventory (LCI) models were developed to provide performance
data for plywood production by tracking all of its inputs and outputs in a gate-to-gate...
Wood adhesives are essential components of wood composites. At
present, the commonly used wood adhesives, phenol-formaldehyde (PF)
and urea-formaldehyde (UF) resins, are petroleum-based synthetic resins
that may result in emission of formaldehyde in the production and use of
wood composites. Because the world's oil reserves are naturally limited
and formaldehyde...
Current lathe technology, smaller diameter logs, smaller core diameters, and
the sale of higher grade veneer for use in engineered wood products are all factors
contributing to plywood manufacturers using rougher veneer with different lathe
check characteristics. When rough veneer is encountered, plywood manufacturers
typically increase the adhesive spread rate...
The objective of this research is to use a three-dimensional (3D) analysis
method to include 'system effects' directly in the design of light-frame roof truss
assemblies. The goal of this study is to develop an improved and practical method to
determine the structural performance of 3D roof truss assemblies used...
The objective of this study is to complete life cycle inventories (LCI) for laminated veneer lumber (LVL) and composite I-joist (I-joist) production in the two main forest products producing regions in the U.S., the Pacific Northwest (PNW) and Southeast (SE). LVL and I-joists are composite wood building materials that are...
The internal structure of natural fiber composites can be manipulated by controlling the spatial distribution of fiber orientation and internal chemical and thermodynamic conditions during their consolidation. Objects highly tailored to specific service demands may thereby be produced. Techniques to form miniature structural beams from oriented hemp and random wood...
Friction dampers have been used successfully to dissipate seismic
energy in steel and concrete structures. The application is new to timber
structures. The objectives of this research were to design a slotted bolted
connection (SBC) and evaluate its potential as a passive energy damper in
timber brace.
The research was...
Torsion test was evaluated as a method to determine the shear strength
parallel to grain of full-size structural composite lumber (SCL). Experimental
results of eighty-five rectangular (44 x 140 mm²) specimens were verified by finite
element analysis. Laminated strand lumber (LSL), laminated veneer lumber
(LVL) and parallel strand lumber (PSL)...
The objectives of this study are: (1) to evaluate the effect of reference
displacement on wall behavior under fully reversed cyclic loading using the
CUREE test protocol and (2) to assess damage accumulation (visible fastener
damage and stiffness degradation) for the imposed drift levels. All tests were
conducted on identical...
Copper is an excellent biocide which has a long history of usage for protecting wood from deterioration, but some organisms have developed tolerance for this chemical. Copper tolerance among wood decay fungi is a poorly understood phenomenon that is gaining importance as cofactors such as arsenic and chromium are removed...
The objective of this study was to determine the effect of misplaced hold-downs
on the static and cyclic behavior of wood shear walls. Three shear wall
configurations were considered in this study. The first configuration (control) had
hold-downs at the ends of the wall (wall type 1), the second configuration...
The gravitational component of water potential and frictional resistance during transpiration lead to substantial reductions in leaf water potential (Ψl) near the tops of tall trees, which can influence both leaf growth and physiology. We examined the relationships between morphological features and gas exchange in foliage collected near the tops...
Use of Granier-style heat dissipation sensors to measure sap flow is common in plant physiology, ecology and hydrology. There has been concern that any change to the original Granier design invalidates the empirical relationship between sap flux density and the temperature difference between the probes. Here, we compared daily water...
This study investigated the mechanisms involved in the
regulation of stomatal closure in Douglas-fir and evaluated
the potential impact of compensatory adjustments in
response to increasing tree height upon these mechanisms.
In the laboratory, we measured leaf hydraulic conductance
(Kleaf) as leaf water potential (Yl) declined for comparison
with in...
Douglas-fir trees from 39 open-pollinated families at four test locations were assessed to estimate heritability of modulus of elasticity (MOE) and basic density. After trees were felled, sound velocity was measured on 4-m logs with the Director HM200. Disks were taken to estimate dry and green wood density; dynamic MOE...
We determined the axial and radial xylem tension gradients in trunks of young Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) trees. Axial specific conductivity (ks-a) and sap flux density (Js) were measured at four consecutive depths within the sapwood at a stem height of 1 m. By definition, at a given position...
Wood density, moisture content, tracheid width and cell wall size were examined in trees from plots that were sprayed for 5 years with chlorothalonil (Bravo®) fungicide to reduce the impact of Swiss needle cast (SNC) and from trees in adjacent unsprayed plots. The unsprayed (more heavily diseased) trees had significantly...
1. The xylem pressure inducing 50% loss of hydraulic conductivity due to embolism
widely used for comparisons of xylem vulnerability among species and across aridity
However, despite its utility as an index of resistance to catastrophic xylem failure
drought, P5o may have no special physiological relevance in the context of...
Our goals were to quantify how non-embolism-inducing pressure gradients influence trunk sapwood specific conductivity (ks) and to compare the impacts of constant and varying pressure gradients on ks with KCl and H2O as the perfusion solutions. We studied six woody species (three conifers and three angiosperms) which varied in pit...
Engineering analysis of heavy timber structures under dynamic loads
is generally lacking. Some literature suggests that heavy timber structures
are stiffer than expected, but popular engineering opinion is to the contrary.
In addition, prior research has shown that passive friction dampers can be
used in timber structures for the intended...
Bark plays a critical role in the life of a tree when it is standing. Once the tree is felled, however, bark has minimal value and
may be a net financial loss to the forest industry. Because of bark’s limited worth, logs are often bought and sold based on under...
• Hydraulic vulnerability of Douglas-fir (Pseudotsuga menziesii) branchlets
decreases with height, allowing shoots at greater height to maintain hydraulic
conductance (Kshoot) at more negative leaf water potentials (Ψl).
• To determine the basis for this trend shoot hydraulic and tracheid anatomical
properties of foliage from the tops of Douglas-fir trees...
• A technique for measuring in vitro respiration was investigated to understand why rates were higher than those reported in vivo and to elucidate trends within mature Pseudotsuga menziesii (Douglas‐fir) trees.
• Extracted increment cores were divided into 3–4 radial depths and a gas chromatograph was used to compare respiration...
• Compression wood has been shown to reduce stem permeability, but it is not known to what extent it affects leaf‐level processes. Here, we report whole‐plant hydraulic properties of Douglas‐fir (Pseudotsuga menziesii) seedlings induced to form varying amounts of compression wood.
• Seedlings were grown under three bending treatments to...
• There are two optima for maximizing hydraulic conductance per vasculature volume in plants. Murray's law (ML) predicts the optimal conduit taper for a fixed change in conduit number across branch ranks. The opposite, the Yarrum optimum (YO), predicts the optimal change in conduit number for a fixed taper.
•...
The air‐seeding hypothesis predicts that xylem embolism resistance is linked directly to bordered pit functioning. We tested this prediction in trunks, roots, and branches at different vertical and radial locations in young and old trees of Pseudotsuga menziesii. Dimensions of bordered pits were measured from light and scanning electron micrographs,...
This research investigated the longevity of functional connections between leaf traces and stem xylem in 16 species of conifers to better understand the spatial use of sapwood for water transport. The first question was which ring(s) stained when a vacuum was applied to the distal end of the cut surface...
Despite renewed interest in the nature of limitations on maximum tree height, the mechanisms governing ultimate and species-specific height limits are not yet understood, but likely involve water transport dynamics. Tall trees experience increased risk of xylem embolism from air-seeding because tension in their water column increases with height due...
While wood plastic composites have gained an increasingly large share of the market for decks and other outdoor structures, there are many questions about the long-term potential for biodeterioration of these materials. While the plastic does appear to retard moisture uptake, thereby slowing the rate of degradation, a number of...
Many paper products like towel and tissue cannot serve their purposes without temporary wet strength Glyoxal-polyacrylamide (GPA) resin is one of the widely used commercial wet strength additives that impart the temporary wet strength to paper and paperboard products However, GPA resin is derived from petrochemicals and contributes to contaminants...
Current compression perpendicular-to-grain (c-perp) design values for wood members are based on mean stress using the ASTM D143 specimen. Base design value, as determined from 0.04-in deformation in the ASTM specimen, is applied to all c-perp applications. While the standard ASTM test was presumably believed to adequately reflect relevant c-perp...
While microbial colonization of wood is presumed to be characterized by a myriad of interactions between numerous organisms, studying these processes is often difficult owing to the opaque nature of the wood and the inability to readily distinguish among the many species colonizing the material. One method for enhancing the...
High density polyethylene (HDPE) is a ubiquitous material with versatile properties. It is produced and used in greater volume than any other thermoplastic. HDPE is often filled with a variety of materials for various applications. Glass fiber and wood flour are two common fillers for HDPE. Recently there has been...
Microchannel devices are rapidly evolving process technology with a wide variety of applications. Microchannel devices hold the potential to transform many separation processes. One potential application for such microchannel devices is kidney dialysis. By reducing the size and cost of the device, this technology offers the potential to allow dialysis...
This research studied the effects of changing from a traditional manufacturing
system to a cell manufacturing system in a value-added wood products company.
Discrete event simulation was used to describe the current system and the proposed
new systems. Parts were separated into part families that shared similar processing
requirements. From...
Wood remains the most popular material for deck construction. For centuries, consumers have chosen wood because of its desirable qualities and aesthetics. In recent years, wood plastic composites (WPC's) have seen rising demand as alternatives to wood decks, despite a large price premium. In addition, the removal of CCA treated...
We sampled boles, branches, and roots of four Douglas-fir (Pseudotsuga menziesii var. menziesii) trees to learn a) whether branches and roots have a zone of juvenile wood, defined as a zone with progressive changes in wood density and/or tracheid length from the pith outward at successively greater cambial
ages, and...
The air permeability of western hemlock from coastal forests in western Oregon was assessed. Permeability varied widely among trees, as well as by position within individual trees. Permeability tended to decrease with distance inward from the bark, a trend implying that this species produces a heartwood zone. These variations may...
We studied the feasibility of using end-grain characteristics to match individual boards and cants back to their parent Douglas-fir (Pseudotsuga menziesii) logs. After reviewing marking/reading and biometric automated identification systems, we focused on end-grain biometrics because they appear to have the most promise for sawmills. Biometric identification requires that every...
The fact that 80 percent of Mexican forestlands are under common ownership impacts the competitiveness of the forest products industry and forest sustainability. Community forest enterprises (CFE) are a heterogeneous group of forest industries managed by indigenous and local communities for livelihood and profit. Many CFEs face inner competitiveness problems,...
The cohesion-tension theory of water transport states that hydrogen bonds hold water molecules together and that they are pulled through the xylem under tension. This tension could cause transport failure in at least two ways: collapse of the conduit walls (implosion), or rupture of the water column through air-seeding. The...
The width of earlywood and latewood in conifer xylem may have a profound effect on water transport and storage, vulnerability to embolism, and wood strength, yet the controls over the timing of latewood formation are unclear. Tracheids differentiating in the cambial zone are influenced by IAA indole-3 acetic acid, the...
Cross-sectional disks were cut at two stem heights (1.5 m and 3.0 m) from 9-year-old trees of three Populus clones grown in an intensively-cultured plantation in western Washington. At age 1.5 years, when the trees averaged 3.4 m tall, half of the trees were pruned by removing all branches below...
This paper reviews literature on the formation of heartwood and on the components that affect natural durability. It includes discussion about the function of heartwood in living trees, factors influencing the natural durability of heartwood, the process of heartwood formation, and variations in heartwood quantity and quality. Heartwood formation is...
It would be valuable economically to know what are the biological triggers for formation of mature wood (currently of high value) and (or) what maintains production of juvenile wood (currently of low value), to develop silvicultural regimes that control the relative production of the two types of wood. Foresters commonly...
Isolation, detection with diagnostic polymerase chain reaction (PCR), and microscopy demonstrated the presence of Phytophthora ramorum in the sapwood of mature, naturally infected tanoak (Lithocarpus densiflorus) trees. The pathogen was strongly associated with discolored sapwood (P < 0.001), and was recovered or detected from 83% of discolored sapwood tissue samples....
Innovativeness can help companies differentiate themselves, with the ultimate goal of securing survival and improving performance. Modern theories in organizational behavior look at innovation as something that starts with individual creativity but that is also affected by the work environment. Using one broad industry sector, the US forest products industry,...
In this case, the student is a senior partner in Corporate Planning Group (CPG), a strategy-consulting firm. The principals of National Systems, Inc. (the company) have retained CPG to develop a 5-year strategic marketing program to (1) strengthen current markets and (2) develop new markets for the company’s line of...
This case study describes in detail how to conduct a performance review of forest product industries. This case study uses the paper industry for illustration, but the principles and methods presented are such that you will be able to conduct a performance review in any industry.
In this case study, Willamette Industries, Inc. explores the potential of environmental marketing. The company conducted research to determine the views of their customer base. Based on this information and a description of the company’s external
environment, students are asked to recommend a marketing strategy.
Tanoak (Lithocarpus densiflorus (Hook. and Arn.) Rehder) is highly susceptible to sudden oak death, a disease caused by the oomycete Phytophthora ramorum Werres, De Cock & Man in’t Veld. Symptoms include a dying crown, bleeding cankers, and, eventually, death of infected trees. The cause of mortality is not well understood,...
Rubber without reinforcement has limited applications. The strength of reinforced rubber composites can be ten times stronger than that of unreinforced rubbers. Therefore, rubber composites are widely used in various applications ranging from automobile tires to seals, valves, and gaskets because of their excellent mechanical elastic properties. Silica and carbon...
Every wood anatomist knows that the wood near the center of a tree (juvenile wood) differs from the wood laid down at some distance from the pith (mature wood), and that the wood produced during the spring (earlywood) differs from the wood produced during the summer (latewood). There is a...
The importance of wood bonding increased in the last decades due to the
increased usage of wood composites whose performance depends to a large extent on
the adhesive penetration and subsequent bonding of the adherends. The presented
research used XMT (x-ray microtomography) to perform a non-destructive, threedimensional
analysis of the...
Hygro-mechanical effect is a general term applied to all phenomena that involves interaction between moisture content and mechanical characteristics of hygroscopic materials by analogy to thermo-mechanical effects. The hygromechanical effects include (but are not limited to) free shrinkage/swelling, effect of moisture on elastic modulus, strength, creep, failure mechanisms, and mechano...
In deciduous species, water exits stems mainly through leaf traces
attached to the outer growth ring and yet we know that water ascends
throughout the entire cross-section of the sapwood. There is an increasing
amount of information on sap flow and sapwood hydraulic properties from
separate studies, but little information...
Lead-user research is a relatively new marketing research technique, and it has not seen much use in the forest sector. Lead-user research is designed to capture not just the needs of the customer in their own voice but also to involve actual users of goods and/or services in their development....
Society uses massive quantities of wood fiber in production of paper, and demand for fiber is projected to increase further as production of biofuels from fermentation of plant cellulosic materials increases. Because these end uses generally require the costly step of removing of lignin, wood with reduced or more easily...
Non-destructive commercial ultrasonic grading provides laminated veneer lumber (LVL) manufacturers a means for sorting veneer based on average ultrasonic propagation time (UPT) and/or average dynamic modulus of elasticity (MOEd). While this may provide reliable estimations of modulus of elasticity (MOE), little is known about the influence of veneer defects on...
The fundamental intent of the study was to develop an innovative wood-strand composite for use in structural applications. Plantation grown, low density, hybrid poplar was used in the study which was found to be appropriate for the underlying Viscoelastic Thermal Compression (VTC) process. Wood modified by this process has high...
Synthetic adhesives like phenol formaldehyde (PF) and isocyanates dominate the
wood based structural panel market. The raw materials that makeup these adhesives
are based on petroleum and natural gas. The sustainability and the continued success
of the wood based structural panel industry will benefit from the development of
alternative adhesives...
The essential oil components of cedar heartwoods play an important role in the durability of these trees. Yet, the composition of these oils and identity of many of the compounds remains unknown, or incompletely know for some commercially important cedar heartwoods. The essential oil extracts of Alaska Yellow Cedar (Chamaecyparis...
An increment core-based, laboratory method was used to measure tissue-level respiration under controlled temperature (termed respiratory potential) of eleven tree species from three age classes. Respiratory potential was calculated on a basis of core dry-mass, volume, carbon, or nitrogen content and live bole volume. Methods tests suggested that core carbon...
When Douglas-fir and red alder grow in mixture, interactions between the two species can be competitive, facilitative, or a combination of both over time. A number of factors have recently led to increased interest in managing these two species together for commercial production, and ongoing investigations are yielding important information...
In recent years, log structures have been marketed as an alternative
to conventional light-frame wood structures. Log structures are constructed
using round timbers (or manufactured timbers) that are stacked vertically
and have interlocking corners. Thru-rods and lag screws are used to
provide inter-log connections. This project was conducted to evaluate...
Service life prediction models for light-framed wood structures require an extensive quantity of empirical data on deterioration pathologies for the numerous structural components, as well as mechanistic approaches to determine their capacity at various levels of deterioration. The data and models presented in this study satisfy a portion of the...
The goal of this study was to develop an understanding of the nature of surge wave loading on
wood framed residential structures for a variety of building configurations and test conditions.
The objectives of the study were: (1) to measure forces on a 1/6th scale wood framed
residential structure, (2)...
The fabrication of nano-scale devices is a challenging, but potentially important, technology that has drawn a great deal of interest among researchers. Such nanoscale constructions utilizing a bottom-up approach for device building have many foreseeable applications in areas as diverse as miniaturized electronics, sensors, and biomedical devices.
One of the...
The effects of incorporation of selected biocides on physical and mechanical properties of aspen strandboard were assessed using five copper-based preservatives or zinc borate at three retention levels. Tebuconazole or 4,5-dichloro-2-N-octyl-4-isothiazolin-3-one (DCOI) were added as co-biocides to selective copper-based treatments. Mold box tests showed that only panels treated with DCOI...
The overall goal of this study was to evaluate an alternative to
traditional wood framed shear wall construction. This study introduced the
innovative idea of using a water and seismic damage resistant, wood-concrete-
composite (WCC) construction instead of an all-wood design. The
WCC design consisted of a thin shell of...
In many composites, fiber bridging develops as part of the fracture process. Fiber bridging invalidates many toughness evaluation methods such as the ASTM E399 and complicates the identification of crack length, which is a necessary parameter in energy methods. In order to measure the toughness of fiber bridging composites, an...
Business is a social institution and society has always designated a role for
business which has been undergoing changes with changing societal values and
paradigms. Thus while business has always had some responsibilities, the modern
connotation of the words corporate social responsibility commonly refers to business
assuming responsibilities in economic,...
The tendency of wood to shrink and swell with changing moisture content remains as one of the most significant challenges to using wood in its many applications. Viscoelastic Thermal Compression (VTC) has been shown to significantly increase the density, strength and stiffness of wood. However, dimensional stability is still a...
While the heartwood of many wood species exhibits excellent resistance to fungal and insect attack, this resistance is sometimes diminished in second-growth material of the same species. The reasons for the reduced durability are unclear, but they may reflect a combination of both higher proportions of sapwood as well as...
Co-located mills that share a log resource through a single merchandising
facility are challenged with the task of allocating the costs of joint-products in order to
determine log cost for each mill during a given period. While allocating joint-costs is
inherently arbitrary, some allocation must be made to include raw...