Index Catalog // ScholarsArchive@OSU

A numerical solution for heat transfer to non-Newtonian fluids with temperature-dependent viscosity for arbitrary conditions of heat flux and surface temperature

Creator:: Cochrane, G. F. (Glenn Frank)
Resource Type:: Dissertation
Full Text:: encouragement of the author's major advisor Dr. James R. Welty are gratefully acknowledged. His efforts were a

Heat and mass transfer rates associated with the drying of Southern pine and Douglas fir veneer in air and in steam at various temperatures and angles of impingement

Creator:: Laity, Walter William
Abstract:: Southern pine and Douglas fir veneer samples were dried in air under the following conditions: air temperatures were 350, 600, and 750°F; air velocities were 50, 100, and 150 feet per second, and angles of impingement of air against the veneer surfaces were 0°, 45°, and 90°. The resulting drying...
Resource Type:: Masters Thesis
Full Text:: in Air and in Steam at Various Ternpertures ap.d 4ngles of Im Abstract approved: James R. Wlty

Cold trap performance : a general analysis

Creator:: Rothwell, Micheal Olin
Abstract:: A cold trap is a device used to remove certain impurities from a liquid metal by controlled precipitation of such impurities. An investigation of the thermal characteristics of laminar flow in two air-cooled cold traps was made. This investigation showed that the sodium heat transfer rate is a function of...
Resource Type:: Masters Thesis
Full Text:: for Privacy Abstract approved: James R. Wjlty A cold trap is a device used to remove certain

Drying rates of Douglas fir veneer in superheated steam

Creator:: Atherton, George H. (George Harry), 1920-1987
Resource Type:: Masters Thesis
Full Text:: - tures 400 F, 600 F, and 800 F were used. Drying times from an initial moisture content of about 57

Heat generation rates of nonfissionable materials in a nuclear reactor environment

Creator:: Zimmerman, Paul James
Abstract:: Radiation induced heat generation rates of several nonfissionable materials were measured calorimetrically in a nuclear reactor environment. The calorimeter was uniquely designed to allow many materials of grossly different heat generation rates to be measured. heat transfer characteristics of the calorimeter were determined analytically and experimentally. Materials were chosen to...
Resource Type:: Masters Thesis
Full Text:: Rates of Nonfissionable Materials In A Nuclear Reactor Environment by Paul James Zimmerman A THESIS

An analytical model of heat transfer to a horizontal cylinder immersed in a gas fluidized bed

Creator:: Adams, Ronald Lynn
Abstract:: A steady gas convection model of heat transfer to a horizontal cylinder immersed in a gas fluidized bed is presented. Contributions due to flow within attached bubbles as well as the interstitial voids are included. The interstitial flow is approximated as flow within a series of double cusped channels and...
Resource Type:: Dissertation
Full Text:: Abstract approved: James R. Welty/ A steady gas convection model of heat transfer to a horizontal

Heat and mass transfer rates associated with the drying of plywood veneer using superheated steam at various angles of impingement

Creator:: South, Veeder, III
Resource Type:: Masters Thesis
Full Text:: TRANSFER RATES ASSOCIATED WITH THE DRYING OF PLYWOOD VENEER USING SUPERHEATED STEAM AT VARIOJ.IS ANG F

The study of active sites and bubble formation frequency in nucleate boiling heat transfer

Creator:: Aoki, Tadao
Abstract:: The heat-transfer mechanism studied in this experiment was pool boiling from a flat horizontal surface facing upward with the bulk liquid at its saturation temperature. The hot-film anemometer probe was introduced to boiling heat-transfer analysis as a possible device for counting active nucleation sites and for other investigations such as...
Resource Type:: Masters Thesis
Full Text:: appreciation goes to Dr. James R. Welty for his valuable suggestions throughout this project. Also I would

The design, construction and calibration of an instrumented surface for convective heat transfer studies

Creator:: Meyers, Stanley Kent
Abstract:: The purpose of this thesis work has been the design, construction and calibration of an instrumented surface for convective heat transfer studies. The surface is in the form of a flat plate roughly 24 inches wide by 48 inches long. It is made up of 48 individual cells, laminated side-by-side...
Resource Type:: Masters Thesis
Full Text:: STUDIES. Abstract approved: Redacted for Privacy James R. 'Welty The purpose of this thesis work has

An experimental study of natural convection in air between a vertical isothermal flat plate and a parallel insulated flat plate

Creator:: Kim, Sung-Soo
Abstract:: Natural convection heat transfer in air between two vertical plates 38 by 24 inches was investigated in this work with spacings between the plates of 0.625, 1.0 and 1.75 inches. One plate was isothermal and the other adiabatic. To measure the point velocities in the air layer a very thin...
Resource Type:: Masters Thesis
Full Text:: FLAT PLATE AND A PARALLEL ,INSULATED. FLAT PLATE Redacted for privacy James R. Welt Abstract approved

ScholarsArchive@OSU

A numerical solution for heat transfer to non-Newtonian fluids with temperature-dependent viscosity for arbitrary conditions of heat flux and surface temperature

Heat and mass transfer rates associated with the drying of Southern pine and Douglas fir veneer in air and in steam at various temperatures and angles of impingement

Cold trap performance : a general analysis

Drying rates of Douglas fir veneer in superheated steam

Heat generation rates of nonfissionable materials in a nuclear reactor environment

An analytical model of heat transfer to a horizontal cylinder immersed in a gas fluidized bed

Heat and mass transfer rates associated with the drying of plywood veneer using superheated steam at various angles of impingement

The study of active sites and bubble formation frequency in nucleate boiling heat transfer

The design, construction and calibration of an instrumented surface for convective heat transfer studies

An experimental study of natural convection in air between a vertical isothermal flat plate and a parallel insulated flat plate

Limit your search

Academic Affiliation

Advisor

Commencement Year

Committee Member

Creator

Date

Decade

Degree Field

Degree Level

Degree Name

Language

Non-Academic Affiliation

Peer Reviewed

Resource Type

Rights Statement

Subject

Search Constraints

Search Results

Limit your search