Index Catalog // ScholarsArchive@OSU

Laminar natural convection within long vertical uniformly heated parallel-plate channels and circular tubes

Creator:: Vorayos, Nat
Abstract:: The problem of simple mathematical models of laminar natural convective flow within a long vertical parallel-plate channels and circular tubes kept at uniformly heated walls is revisited to seek a clear physical understanding of heat transfer mechanisms. A series solution method to analyze the fully developed flow and an integral...
Resource Type:: Dissertation
Full Text:: ............................................................................ 154 A.2 Distribution of a ratio Rm C2m1C2m-i-21 for the UWT circular tube problem

Fluid forces on and flow configurations around a circular cylinder near a plane boundary

Creator:: Tavolacci, Don
Abstract:: The flow configurations around and the forces acting on a circular cylinder with its axis parallel to a nearby plane boundary and subjected to a uniform flow were investigated. The flow conditions, which were perpendicular to the cylinder axis and parallel to the plane boundary were investigated experimentally and theoretically....
Resource Type:: Masters Thesis
Full Text:: Figure Page 1 Flow around a circular cylinder 25 2 Relationship between the Reynolds number and the 26

Boundary layer control tests by suction on a circular cyclinder wing section

Creator:: Dennon, Jack Dwight
Resource Type:: Masters Thesis
Full Text:: wall of a circular cylinder, when the external flow is attached, will be distributed according to 2

Monte Carlo simulation of radiation heat transfer in a three-dimensional enclosure containing a circular cylinder

Creator:: Hong, Seung-Ho
Resource Type:: Masters Thesis
Full Text:: ) there is no other convenient method, (2) a simple procedure is needed to check the validity of a new

An experimental determination of coefficients for the contraction and diffusion of submerged jets in series.

Creator:: Heacock, Harold Wendall
Resource Type:: Masters Thesis
Full Text:: --._ - ,.----,-. /N ., I ,/ N - -_ / / _ / / /7-7-7 / , /T / / / / / 77/ /( ORIFICE NO. I ORIFICE NO. 2 ORIFICE

Hydrodynamic signatures of a 2-D gas-solid fluidized bed

Creator:: Kopczynski, Sean Peter
Resource Type:: Masters Thesis
Full Text:: in Figure 2-7. When opaque particles occupied the gap, no light was transmitted and consequently

Evaluation of Materials for Use in Open-Cycle Magnetohydrodynamic Power Generation

Creator:: Bowen, Michael S.
Abstract:: Recent interest in oxy-fuel combustion for carbon capture, as well as advancements in technologies such as magnetics, materials, and computational modeling has sparked renewed interest in magnetohydrodynamic (MHD) power generation. The increased temperatures of oxy-fuel combustion versus air-fuel combustion poses a challenge in the selection of materials for plasma exposed...
Resource Type:: Masters Thesis
Full Text:: experimental methods performed in Chapter 2, assisting in developing the fabrication and measurement

The Mira 2 Rocket Engine: Applying Lessons Learned for an Improved Iteration

Creator:: Dimas-Harms, Colton R.
Abstract:: In this paper, I present the design of Mira 2, a small-scale, liquid bipropellant rocket engine, with a specific focus on its oxidizer-centered pintle injector. Building upon the valuable lessons and insights gained from the empirical testing of its predecessor, Mira 1, the Mira 2 engine incorporates several improvements and...
Resource Type:: Capstone Project
Full Text:: Mira 2 Rocket Engine: Applying Lessons Learned for an Improved Iteration Abstract approved: Kyle

The theoretical design and construction of a .25 calibre automatic repeating rifle

Creator:: Winniford, John Franklin
Abstract:: In the construction of a rifle for sporting or target work there are several conditions to be met. In the first place the rifle must be made to balance easily.at all times, whether the magazine is full of loaded cartridges or is empty. In all cases the barrel of the...
Resource Type:: Undergraduate Thesis
Full Text:: Repeating Rifle. libmitted to the Faculty of the 0 REGON AGRICULTURAL COLLEGE= = = liCZ =2 = =2 for the

Repeated stress tests on carbon steels variously heat treated

Creator:: Morris, Homer Blair
Resource Type:: Masters Thesis
Full Text:: ------------------- -, General te1 No. i approximately O.'3J. C.rbon, o. 2, ).ó'), C s Steel :To. 2 annealed at 1450 úe.rees

ScholarsArchive@OSU

Laminar natural convection within long vertical uniformly heated parallel-plate channels and circular tubes

Fluid forces on and flow configurations around a circular cylinder near a plane boundary

Boundary layer control tests by suction on a circular cyclinder wing section

Monte Carlo simulation of radiation heat transfer in a three-dimensional enclosure containing a circular cylinder

An experimental determination of coefficients for the contraction and diffusion of submerged jets in series.

Hydrodynamic signatures of a 2-D gas-solid fluidized bed

Evaluation of Materials for Use in Open-Cycle Magnetohydrodynamic Power Generation

The Mira 2 Rocket Engine: Applying Lessons Learned for an Improved Iteration

The theoretical design and construction of a .25 calibre automatic repeating rifle

Repeated stress tests on carbon steels variously heat treated

Limit your search

Academic Affiliation

Advisor

Commencement Year

Committee Member

Conference Name

Creator

Contributor

Date

Decade

Degree Field

Degree Level

Degree Name

File Format

Language

License

Non-Academic Affiliation

Peer Reviewed

Resource Type

Rights Statement

Subject

Search Constraints

Search Results

Limit your search