This research examined the potential for using peanut husk as a fiber alternative to wood in the production of melamine-formaldehyde (MF) particleboard. MF resin was used to produce panels with one, three, six, nine or 12 percent resin contents. Modulus of Rupture (MOR), Modulus of Elasticity (MOE), Internal Bond (IB)...
Chainsaw users value cutting performance and safety. Knowledge of the forces exerted during sawing are necessary to understand and improve the cutting performance of saw chain. Additionally, cutting forces can be used to form metrics for evaluating performance tradeoffs when using a safety (i.e. low-kickback) saw chain versus a standard...
:
__________________________________________________________________
John P. Parmigiani
Chainsaw users value cutting performance and safety. Knowledge of
Restoration programs effectively prevent or mitigate wildfires and pest outbreaks in the forest lands. The most common approach is to selectively harvest smaller and dead trees in order to preserve larger and superior trees. Ponderosa pine, Pinus ponderosa, (PP) lumber is one of the common species harvested from restoration programs...
Timber-concrete composite (TCC) solutions originated in the early twentieth century. There has been a renewed interest in TCC solutions in modern mass timber buildings, especially for floor systems. However due to lack of data, design standards, and code acceptance, TCC solutions require that new mass timber solutions be tested, and...
Cross-Laminated Timber (CLT) is a prefabricated building material that is relatively new to the United States and North America. It consists of no less than three layers of graded, dimensional lumber glued in alternating longitudinal and transverse layers to create a panel that can be used for various building applications...
Chainsaws, an indispensable tool for modern forestry operations, rely on bar lubricant to prevent rapid wear of the chain and bar. Choice of bar lubricant must balance performance, cost, and biological impact. Many bar lubricants are available, but little published work exists that conclusively ranks the performance of these choices....
This study computationally and experimentally examines the mechanisms of crack penetration, deflection and the transition between penetration and deflection. The finite element analysis based computational modeling work used strength-and-energy based cohesive-zone approach to study the effect of dimensionless parameters (e.g., interfacial incident angle, fracture-length scale, and normalized toughness) on penetration/deflection...
Most of existing commercial unsaturated polyester (UPE) resins are typically composed of a UPE and a high amount of highly volatile, flammable, and toxic styrene. The emission of hazardous styrene in the handling of the UPE resins and the preparation and use of fiber-reinforced UPE composites poses severe hazards to...
Existing pressure sensitive adhesives (PSAs) are mostly based on petrochemicals. In this study, a novel PSA based on a renewable material, methyl oleate, was prepared and characterized. Methyl oleate was first epoxidized to form epoxidized methyl oleate that was subsequently hydrolyzed and acidified to form epoxidized oleic acid (EOA) which...
Cellulose nanocrystals (CNCs) have received considerable attention over the last ten years because CNCs can be produced from renewable materials such as straw, wood, cotton, and sea animals (tunicates). CNCs are slender rods with high aspect ratios (10-100) and the final dimensions of the CNCs depend on the starting material....
This thesis presents two new approaches for the broadband, time-domain modeling of lossy transmission lines. Each approach is based on an alternative derivation of delay extraction in order to separate the line's linear phase from its
attenuation and dispersion. Augmentation networks represent the derived attenuation networks as rational function approximations....
The Advent of multi-cores allows programs to be executed much faster than before. Cryptoalgorithms use long-bit words thus parallelizing these operations on multi-cores will achieve significant performance improvement. However, not all long-bit word operations in cryptosystems are suitable for parallel execution on multi-cores. In particular, long-bit words used in Elliptic...
Dental resin composites are widely used in modern dentistry due to their aesthetic appearance. However, resin based restorations have inferior mechanical properties (fracture is the second reason for restorations replacement) in comparison to alloy based composites and their antimicrobial properties still remain poor, leading to secondary tooth decay development on...
Understanding the mechanical behavior of composite materials requires extensive knowledge of fracture behavior as a crack approaches an interface between the bulk material and the reinforcement structure. Overall material toughness can be greatly influenced by the propensity of an impinging crack to propagate directly through the substrate or deflect along...
The fundamental intent of the study was to develop an innovative wood-strand composite for use in structural applications. Plantation grown, low density, hybrid poplar was used in the study which was found to be appropriate for the underlying Viscoelastic Thermal Compression (VTC) process. Wood modified by this process has high...
Spraying of liquid adhesive onto wood surfaces has shown to be a highly effective and efficient method of application across many different wood-based composite industries. However, the dynamics of spraying are extremely variable and distribution can be affected by liquid properties (rheology, molecular weight distribution, and temperature), application parameters (disk...
Wood composites are an important renewable structural material which can be a net carbon sink when used in combination with sustainable forest management practices and high rates of log utilization. Adhesive bondlines are an essential part of composites, and for wood composites, they determine the moisture durability and mechanical performance...
Cross-laminated timber (CLT) is a massive engineered wood product made of orthogonally bonded layers of solid-sawn lumber, and is intended for roof, floor, or wall applications. Although it was developed in Europe in the early 90s, CLT is relatively new to North America.
CLT products must be certified for structural...
The mechanical performance of composite materials is determined by the mechanical properties of their individual components and the effective load transfer between these components. Binders are commonly used to bond composite components together and to provide effective load transfer between them. In wood-based composites the binder-component load transfer occurs at...
There is no doubt that adhesive penetration plays an important role in wood bondline joint performance and durability; yet, to date there is no direct experimental evidence linking penetration depth with bond performance. This is, in part, because adhesive penetration is commonly assessed with various 2D microscopy techniques that are...