A procedure for automating the design and layout of analog-to-digital converters (ADCs) is presented. This procedure makes use of the existing synthesis and place-and-route tools that are common in digital circuit design. A method for adding rudimentary analog cells to the standard library is described, allowing the designer to synthesize...
Incremental ADCs (IADCs) have many advantages for low-frequency high-accuracy data conversion—they are easy to multiplex between channels, need simpler digital decimation filter, and allow extended counting with a Nyquist-rate ADC. A single-loop incremental ADC was designed and fabricated in 90 nm for a biosensor interface circuit. It incorporates one integrator,...
In this dissertation, a new Δ∑ A/D converter is presented that is ideally suited for communication applications. It is based on a single-loop single-stage structure, which can realize a high maximum out-of-band quantization noise gain while maintaining stable operation and thus achieve 14-bit resolution at 8 times oversampling. A fifth-order...
With the ever-increasing demand for portable devices used in applications
such as wireless communication, mobile computing, consumer electronics, etc.,
the scaling of the CMOS process to deep submicron dimensions becomes more
important to achieve low-cost, low-power and high-performance digital systems.
However, this downscaling also requires similar shrinking of the supply...
This dissertation presents two high-speed pipeline successive approximation analog-to-digital converters (SAR ADCs). Capacitive DACs and resistive DACs are utilized in these two pipeline SAR ADCs, respectively.
The pipeline SAR ADC with capacitive DACs can save 50% switching power compared with other time-interleaved SAR ADCs since the total capacitance of the...
Ultra-high-speed (>10GS/s), medium-resolution (5~6bit), low-power (<50mW) analog-to-digital converter can find it application in the areas of digital oscilloscopes and next-generation serial link receivers. There are several challenges to enable a successful design, however. First, the time-interleaved architecture is required in order to achieve over 10GS/s sampling rate, with the trade-off...
Data converters are ubiquitous building blocks of a signal chain. The rapid increase in
communication and connectivity devices presents new avenues for pushing the state of
the art analog to digital converters. Techniques for improving resolution, bandwidth,
linearity and bit-error rate, while reducing the power, energy and area is the...
Enabled by continued device scaling in CMOS technology, more and more functions that were previously realized in separate chips are getting integrated on a single chip nowadays. Integration on silicon has opened the door to new portable wireless applications, and initiated a widespread use of these devices in our common...
Incremental ADCs (IADCs) have found wide applications in sensor interface circuitry since, compared to ∆Σ ADCs, they provide low-latency high-accuracy conversion and easy multiplexing among multiple channels. On the other hand, continuous-time ∆Σ ADCs (CTDSM) have been receiving more and more attention as a power-efficient solution in targeting medium to...
This dissertation presents an incremental analog-to-digital converter (ADC) with digital digital-to-analog converter (DAC) mismatch correction. A theoretical time-domain analysis technique was developed to predict the noise performance of the incremental ADC, and a new optimization technique was proposed to minimize the output noise.
In the calibration mode, the incremental ADC...
Multi-stage delta-sigma (ΔΣ) architectures, commonly known as MASH, are the preferred choice for analog-to-digital converters (ADCs) used in broadband communication applications, where high-resolution (above 14 bits) and high-bandwidth (several MHz) performances are required. Current state-of-the-art designs are capable of as much as 5-MS/s output data rates with 90-dB SNR. However,...
Delta-Sigma (ΔΣ) analog-to-digital converters (ADCs) are widely used in wireless transceivers. Recently, continuous-time (CT) ΔΣ ADCs gain growing interest in wireless applications for their lower power consumption and wider input bandwidth as compared with the discrete-time (DT) counterparts.
In this thesis, a wideband low-power CT ΔΣ modulator for next generation...
In recent years, there has been growing interest in both industry and academia to use continuous-time (CT) Δ-Σ A/D converters for wideband wireless and wireline communication applications.
So far no reported CT Δ-Σ A/D modulator achieves 14-bit or higher dynamic range (DR) with more than 2MHz signal bandwidth (equivalently 4MS/s)....
Low-distortion architecture is widely used in wideband discrete-time switched-capacitor delta-sigma ADC design. However, it suffers from the power-hungry active adder and critical timing for quantization and dynamic element matching (DEM). To solve this problem, this dissertation presents a delta-sigma modulator architecture with shifted loop delays. In this project, shifted loop...
Continuous process scale-down and emerging markets for low-power/low-voltage mobile systems call for low-voltage analog integrated circuits. Switched-capacitor circuits are the building blocks for analog signal processing and will encounter severe overdrive problems when operating at low-voltage conditions. There are several well-known techniques to bypass the problem. These approaches include: (1)...
In this thesis, a novel Direct-Charge-Transfer (DCT) integrator structure is proposed, which can settle much faster than regular switch-capacitor integrators. A new Spread-Spectrum Dynamic Element Matching (SS-DEM) algorithm is also introduced, which can effectively spread or shape the nonlinearity error of multi-bit DAC in the feedback path, thus improve the...
Advances in electronic systems have lead to the demand for high resolution, high bandwidth Analog-to-Digital Converters (ADCs). Oversampled ADCs are well- known for high accuracy applications since they benefit from noise shaping and they usually do not need highly accurate components. However, as a consequence of oversampling, they have limited...
The exponential rate of advances in modern communication devices in the last several years have brought us higher levels of functionality and performance as well as reductions in physical size and power consumption. To continue this rate of advancement, next generation systems require wider bandwidth and higher resolution ADCs. Additionally,...
Recently, delta-sigma modulation has become a widely applied technique for high-performance analog-to-digital conversion of narrow-band signals. Most of the early designs used discrete-time structure for good accuracy and good linearity. The transfer functions are independent of the clock frequency. However, high unity-gain bandwidths of the opamps are required to satisfy...
The demand for portable electronic systems and the continued
down-scaling of device dimensions resulted in rapid improvement in
the performance of integrated systems. Several low-voltage design
techniques have been proposed to operate analog circuits with sub-1V
supply. However, these techniques require higher power consumption
to achieve large dynamic range while...
Analog-to-Digital Data Converters (ADCs) used in instrumentation and measurements often require high absolute accuracy, including excellent linearity and negligible dc offset. Incremental data converters (IDCs) provide a solution for such measurement applications. Since IDCs are essentially delta-sigma converters with reset operation before each conversion, they retain most of the advantages...
This thesis describes circuit architectures and techniques that facilitate the
automatic synthesis and fabrication of analog-to-digital converters (ADCs). Since
automated synthesis already exists for digital circuits and is part of the digital
circuit design flow, this work demonstrates the feasibility of ADC synthesis with
little or no modification to presently...
For today’s ubiquitous portable devices, innovative integrated circuits with high performance
yet very low power are necessary. As these devices are used to communicate and sense real world signals in the environment, analog-to-digital converters (ADC) and systems are the key interface circuits needed to digitize the sensed information and they...
With the growing demand for portable/consumer electronics, such as digital
audio/video (AV), the downscaling of device dimensions, which enables the
integration of an increasing number of transistors in a single chip, is mandatory.
This trend also continuously pushes the power supply voltage down to reduce the
power consumption and improve...
This dissertation presents a low-power high-resolution delta-sigma ADC. Two new architectural design techniques are proposed to reduce the power dissipation of the ADC. Compared to the conventional active adder, the direct charge transfer (DCT) adder greatly saves power by keeping the feedback factor of the active adder unity. However, the...
The most accurate method for performing analog signal processing in MOS (metal-oxide-semiconductor) integrated circuits is through the use of switched-capacitor circuits. A switched-capacitor circuit operates as a discrete-time signal processor. These circuits have been used in a variety of applications, such as filters, gain stages, voltage-controlled oscillators, and modulators. A...
Delta-Sigma (ΔΣ) analog-to-digital converters (ADCs) are traditionally used in high quality audio systems, instrumentation and measurement (I&M) and biomedical devices. With the continued downscaling of CMOS technology, they are becoming popular in wideband applications such as wireless and wired communication systems,high-definition television and radar systems. There are two general realizations...
In this thesis work, a design of 14-bit, 20MS/s segmented digital-to-analog converter (DAC) is presented. The segmented DAC uses switched-capacitor configuration to implement 8 (LSB) + 6 (MSB) segmented architecture to achieve high performance for minimum area. The implemented LSB DAC is based on quasi-passive pipelined DAC that has been...
This thesis proposes a novel technique for the design of pipelined and cyclic ADCs utilizing generalized radix gain stages. Several models have been proposed for the optimization of high performance pipelined ADCs by various researchers. This work builds upon them, using a simple but accurate model to estimate the optimal...
Digital-to-analog converters (DACs) with wide dynamic range and high
linearity are required for high-end audio applications. A multi-bit delta sigma
audio DAC, using a novel gain-correction technique, is described in this thesis. For
widely varying on-chip RC time constant, the DAC gain can be accurately
controlled by the correction circuitry....
This thesis presents a novel algorithmic A/D converter to be used in a biosensor. The converter is capable of a conversion rate of 1.5 bits/phase and hence the required conversion time is reduced. The proposed architecture is analyzed for non-ideal effects and compared with existing algorithmic A/D architectures. The converter...
Multi-Gigahertz sampling rate Analog-to-Digital Converters (ADC) with 5-8 bits resolution are used in many signal communication applications. Unfortunately, the performance of the high speed ADC is limited by the timing accuracy of the sampling clock. A small sampling uncertainty can cause a large error in the sampled voltage and result...
Sensors find a variety of applications in portable electronics, automotive and biomedical solutions. The demand for low power and high dynamic range makes the design of digital sensor readout circuits quite challenging. Traditionally, these circuits are realized using amplifiers with passive feedback or precision analog comparators which are power hungry...
VCO-based ADCs have recently emerged as attractive alternative to conventional DeltaSigma (ΔΣ) modulator architectures. Few salient features of a VCObased ADC are: 1) the quantization noise is 1st order noise shaped, 2) it is an open loop architecture, and, 3) its implementation is mostly digital in nature. Hence, they are...
Multi-level decision feedback equalization (MDFE) is an effective sampled signal processing technique to remove inter-symbol interference (ISI) from disk read-back signals. Parallelism which doubles the symbol rate can be realized by utilizing the characteristic of channel response and decision feedback equalization algorithm.
A mixed-signal IC implementation has been chosen for...
Recently, switched capacitor DC/DC converters are extensively used in portable electronic devices because they feature many advantages, such as high efficiency, small package, low quiescent current, minimal external components and low cost. In this thesis, two step-down switched capacitor DC/DC converters are designed. One has the fixed output options 1.5V,...
The increasing popularity of cellular phones with integrated cameras in the
recent past has led to major improvements in its image quality. However, integration of new features, such as mobile email, video streaming, MP3 etc. tend to put the limitation on image quality as camera phone designers struggle to manage...
An AC/AC converter has been designed and implemented for the purpose of
providing a modular drive system with a Brushless Doubly-Fed Machine (BDFM.) This
converter is to be used in laboratory testing and also as part of a demonstration system in
the field.
All hardware needed to start and run...
Preliminary nuclear design studies have been completed on ten
configurations of nuclear reactors for low power (1-30 kWe) space
applications utilizing thermionic energy conversion. Additional design
studies have been conducted on the TRICE multimegawatt in-core
thermionic reactor configuration. In each of the cases, a reactor
configuration has been determined which...
Incore thermionic space reactor design concepts which operate at a
nominal power output range of 20 to 50 kWe are described. Details of the
neutronic, thermionic, thermal hydraulics and shielding performance are
presented. Due to the strong absorption of thermal neutrons by natural
tungsten, and the large amount of that...
An overall systems design code was developed to model
an advanced in-core thermionic energy conversion based
nuclear reactor system for space applications at power
levels of 10 to 50 kWe. The purpose of this work was to
provide the overall shell for the systems code and to also
provide the...
The advent of superior power semiconductor devices and converter topologies
has renewed interest in ac drive systems. Although considerable research efforts have
gone into improving power electronic converter devices and topologies, very little has
been reported on the overall performance optimization of induction machine drive
systems. The report of the...
Ocean wave energy is a new and developing field of renewable energy with great potential. The energy contained in one meter of an average wave off the coast of Newport Oregon could supply dozens of homes with electricity. However, ocean waves are usually quite irregular which leads to large bursts...
The world’s energy consumption is growing at an alarming rate and the need for renewable energy is apparent now more than ever. Estimates have shown that optimization of the extraction of energy from the ocean could significantly aid the world’s quest for sustainable and affordable energy services for all. From...
With energy prices rising and increasing concern about the influence of fossil fuels on climate change, wave energy systems are on the verge of commercial implementation. These first generation wave energy converters utilize either pneumatics or hydraulics to convert the mechanical energy of waves into electricity. For the last several...
A new circuit technique called Folded Source Coupled Logic (FSCL) has been developed
to implement the digital section of mixed-signal IC applications. This FSCL circuit technique
offers the advantage of low overlap current spikes during the switching transitions
of conventional CMOS gates. This overlap current spike has become one of...
Hybrid electric vehicles (HEV’s) are a very important part of today’s transportation system as they are bridging the gap between fully electric vehicles and conventional internal combustion vehicles (ICV’s). They have much higher efficiencies and lower emissions than ICV’s, while still having the ability to travel long range and refuel...
This thesis describes the adder to be used with the Galaxy computer, which is to be constructed at Oregon State University.
The need for faster, more reliable adders is discussed
along with previous adder designs related to the
Galaxy Fast Carry Adder.
Both the logical design and circuit design of...
The concept of combining arithmetic and memory capability on
a single semiconductor chip has become practical from a system's
viewpoint through the decreased cost of semiconductor memories and
high circuit densities achieved through large scale integration. This
paper describes a model for studying the feasibility of such systems.
An arithmetic-memory...
Due to advances in high-density low-cost VLSI and communication technology,
digital filtering and signal processing are being widely used for real-time signal processing
applications. Given the filter specification, choosing the best filter structure for a given
application is not a trivial task. The choice of a particular filter structure depends...
The objective of this thesis is to design a high speed digital FIR filter. The inputs of the
system come from a Delta-Sigma modulator. This FIR filter takes 1024 inputs,
multiplies them with their coefficients and adds the results. The main design task is to
take the input data, which...
Research in digital computers takes two paths: one uses the
computer as a tool to reach certain objectives; on the other, the computer
itself is the object of research. The NEBULA computer was
built with the latter in mind. The system design and logical design
are described here in detail....
Scaling of CMOS technology has progressed relentlessly for the past several
decades. In order for this unprecedented scaling to benefit the performance of
large digital systems, the communication bandwidth between integrated circuits
(ICs) must scale accordingly. However, interconnect technology does not scale as
aggressively, making communication between chips the major...
As more advanced hybrid electric vehicles begin emerging onto the commercial market, design algorithms for their control become increasingly more complicated. One major hurdle for designers is the mitigation and control of the created high frequency harmonics caused from switching the dc voltage into an ac voltage by use of...
Ocean wave energy is rapidly becoming a field of great interest in the world of renewable energy. Significant advancements in design and technology are being made to make wave energy a viable alternative for our growing energy demands. The two major hurdles for ocean wave energy to make a significant...
Low energy design techniques for digital circuits are examined to determine their suitability for use in a digital logic controller for wireless sensor network nodes. Transistor level simulations are used to evaluate the techniques and those demonstrating an energy reduction are used to implement a digital logic controller. The digital...
A digital phase locked loop (DPLL) and a statistical time-to-digital converter (STDC) were previously fabricated in a 0.35µm, 3.3V SOI CMOS process. This work summarizes these designs and characterizes the measured performance. Simulations supplement the measurements where applicable.
The DPLL was found to reach a locked state under a limited...
A new structure for the implementation of bit/serial adaptive IIR filter is
presented. The bit level system consists of gated full adders for the arithmetic
unit and data latches for the data path. This approach allows recursive
operation of the IIR filter to be implemented without any global
interconnections, minimal...
In modern telecommunication applications, the need for high-reliability and high data rate is important because of factors such as a higher demand in multimedia capability of mobile devices and the exponentially increasing number of subscribers. Wireless communications in today’s technology have many limitations due to channel imperfections, which result in...
Several papers propose the use of on-line arithmetic for signal processing applications implemented on FPGAs. Although those papers provide reasonable arguments for the use of on-line arithmetic, they give only inadequate or incomplete comparisons of the proposed on-line designs to other state of the art solutions on FPGAs. In this...
In cellular telephones, RF power amplifiers consume a significant part of the total phone current. Reducing the average PA current will extend battery life. In GSM systems the handset is commanded by the base station to transmit at power levels lower than full power much of the time. A Doherty...