Search Constraints

Start Over
Filtering by: Creator Lam, Adam Q. Remove constraint Creator: Lam, Adam Q. Academic Affiliation Mechanical, Industrial, and Manufacturing Engineering Remove constraint Academic Affiliation: Mechanical, Industrial, and Manufacturing Engineering

Search Results

  • Human Performance with Multiple UAV Systems: Use Cases and Modeling

    Creator:
    Uriarte, Patrick A.
    Abstract:
    Commercial and public safety usage of Unmanned Aerial Vehicles in the National Airspace is currently restricted by federal regulation. The Federal Aeronautics Association is interested in modifying the restrictions; however, research is needed to study the human factor and required aptitude for a single human operating multiple UAVs. This Master’s...
    Resource Type:
    Capstone Project

  • Designing and creating the Oregon State age and disability simulation suit

    Creator:
    Rahrer, Adam P.
    Abstract:
    Over 54 million people report having disabilities in the United States. In addition, there are 40.3 million people 65 years and older living in America. As the population continues to live longer and problems with obesity continue to increase, the number of people with limited capabilities will escalate as well....
    Resource Type:
    Masters Thesis
    Full Text:
    !";! 835!@7@K?08=7>!<7>8=>K5;!87!?=L5!?7>954!0>/!@47A?51;!Q=83!7A5;=8J!<7>8=>K5!87! =><450;5C!835!>K1A54

  • Structure and Actuation of Cephalopod-Inspired Soft Robots

    Creator:
    Olson, Gina M.
    Abstract:
    Cephalopod-inspired soft robot arms have been studied as a new type of manipulator. These arms have been proposed for reach and grab tasks, underwater locomotion via swimming and walking, and robotic surgery. However, the capabilities of existing soft arms are limited to simple motions and light loads. Arm design has...
    Resource Type:
    Dissertation

  • Characterization and Development of Ni-based Superalloys for Supercritical Carbon Dioxide Applications

    Creator:
    Adam, Benjamin M.
    Abstract:
    The advent of supercritical CO2 as a new heat-exchange medium has seen strong interest from the power industry and the energy research field recently. It is advan- tageous in comparison with other heat-exchange cycles, as it can be operated safely at much higher temperatures and pressures, thus increasing the thermal...
    Resource Type:
    Dissertation
    Full Text:
    AN ABSTRACT OF THE DISSERTATION OF Benjamin M. Adam

  • Towards reliable and survivable ocean wave energy converters

    Creator:
    Brown, Adam C.
    Abstract:
    Ocean wave energy is a new and developing field of renewable energy with great potential. The energy contained in one meter of an average wave off the coast of Newport Oregon could supply dozens of homes with electricity. However, ocean waves are usually quite irregular which leads to large bursts...
    Resource Type:
    Masters Thesis
    Full Text:
    OF THE THESIS OF Adam C Brown for the degree of Master of Science in Mechanical Engineering

  • Experimental study of subcooled water spray cooling using flow symmetric micro-structured surfaces

    Creator:
    Tulchinsky, Alex M.
    Abstract:
    Spray impingement cooling has been shown to be a leading candidate for future high heat flux cooling applications. In general, spray cooling curves consist of three heat flux regimes; single-phase, two-phase and critical heat flux (CHF). CHF is considered the design limit for almost all two-phase cooling applications, as a...
    Resource Type:
    Masters Thesis
    Full Text:
    below the impingement surface. Results are presented as heat flux, q  , versus the wall-to-spray

  • Fused Filament Fabrication of Filled Polymers for Metal Additive Manufacturing

    Creator:
    Barmore, Brenton
    Abstract:
    Additive manufacturing (AM) is a relatively new manufacturing technique that can create high complexity parts out of many materials in low volume. The fused filament fabrication (FFF) is the lowest cost AM process and is capable of producing only thermoplastic components. Powder injection molding (PIM) is a high volume low...
    Resource Type:
    Masters Thesis
    Full Text:
    sincere appreciation to… Professors Sundar V. Atre, David P. Cann, W.E. “Skip” Rochefort, and Adam Z

  • Performance and flow stability characteristics in two-phase confined impinging jets

    Creator:
    Sabo, Michael D.
    Abstract:
    Advances in electronics fabrication, coupled with the demand for increased computing power, have driven the demand for innovative cooling solutions to dissipate waste heat generated by these devices. To meet future demands, research and development has focused on robust and stable two-phase heat transfer devices. A confined impinging jet is...
    Resource Type:
    Masters Thesis
    Full Text:
    , and Adam Damiano for the long hours of data collection they assisted with. TABLE OF CONTENTS Page

  • Geometric Chatter Stability Index for Milling and Modeling of Chip Pulling Effect

    Creator:
    Maulimov, Mukhtar
    Abstract:
    Prediction and mitigation of chatter vibrations in machining operations and optimizing overall machining mechanics are crucial for achieving greater productivity and manufacturing efficiency. This thesis first explores effect of directional relationships on chatter stability in milling process. Based on the directional relationships, a geometry-based chatter stability index (CSI) is proposed...
    Resource Type:
    Masters Thesis
    Full Text:
    would like to thank Josiah Adam Breen for his assistance with the experimental setup that is used in

  • Design Automation for 3D Circuits

    Creator:
    Velayati, Mohammad
    Abstract:
    Traditional electronic systems are usually fabricated via printed circuit boards (PCBs). In a regular PCB, the electronic components are placed and mounted on a two-dimensional board. Such a component layout limits the freedom in the component placement process which results in larger electronic devices. With the use of Additive Manufacturing...
    Resource Type:
    Masters Thesis