A commercially available, three-dimensional (3-D) finite-element (FE) analysis
program was used to model metal-plate-connected (MPC) joints in wooden trusses.
The model's features included consideration of material properties, teeth-to-grain-to-direction-
of-force orientation, and wood-to-wood contact. Non-linear spring elements,
placed on the wood surface between wood and plate, were used to represent wood-to-teeth...
The objectives of this research were to evaluate the
behavior of actual metal-plate-connected (MPC) tension-splice
and heel wood truss joints under seismic loads from the
Northridge earthquake (tension-splice joints only) and under
loads from a large artificial earthquake (1.0 g's and 0.67
g's maximum horizontal and vertical accelerations,
respectively). A...
Metal-plate-connected (MPC) trusses have traditionally been designed based on a
tributary load distribution and a simplified truss model. This design method ignores the
load-sharing and composite action in MPC roof truss systems, the semi-rigidity of MPC
joints, and joint eccentricity.
The main objective of this study was to provide a...
The torsion test was evaluated as a method for determining the shear
strength of full-size structural lumber. The evaluation involved an experimental
length study, an experimental depth study, and a finite element study.
The length study consisted of fifty nominal 2x4 specimens, ten specimens
for each length, and ten American...
The objective of this research was to develop a one-third scale model of full-size
(prototype) metal-plate-connected (MPC) wood truss joints using similitude theory. The
prototype metal connector plates in MPC joints were modeled using thin galvanized sheet
metal and short staples. Truss grade wood material was ripped to one-third scale...
The objective of this research was to evaluate the duration of load factor for
metal-plate-connected (MPC) truss joints subjected to various cyclic loading conditions.
Heel and tension-splice joints from a standard 30-foot span Fink truss constructed from
nominal 2x4 Douglas-fir lumber were tested. A testing frame similar to that developed...
This study presents a practical method to model an actual Metal-Plate-
Connected (MPC) roof truss assembly using a commercial program, SAP2000, to
investigate its system performance. Truss assembly modeling was examined
because the conventional single truss design method ignores system effects, such as
variability of modulus of elasticity (MOE), interaction...
The objectives of this study are: (1) to evaluate the effect of reference
displacement on wall behavior under fully reversed cyclic loading using the
CUREE test protocol and (2) to assess damage accumulation (visible fastener
damage and stiffness degradation) for the imposed drift levels. All tests were
conducted on identical...
Many publications, documents, codes and guidelines exist related to the seismic evaluation and rehabilitation design of existing buildings. This report discusses the assumptions and methods employed for investigation of two wood structures using four references: FEMA 154, FEMA 356, ASCEI per SEI 31, and 1997 UBC. The screening performed using...
The objectives of this study were to evaluate the performance of wood frame shear walls
under monotonic, cyclic and earthquake loads by: (1) estimating the variability of shear wall
performance, (2) comparing the performance of walls under each loading protocol, (3) evaluating
the effects of anchorage on wall performance, and...
The overall goal of this study is to evaluate the earthquake performance of wood frame
shear walls, and more specifically: (1) to compare the performance differences of fully and
partially anchored walls under monotonic, cyclic, and earthquake loads, (2) to compare wall
performance under earthquake loads with that of standardized...
During the past several decades, earthquakes have caused extensive damage to
buildings, including wood-frame, single-family dwellings, in the United States. In
order to mitigate future losses, existing buildings in earthquake prone areas should be
evaluated for their seismic safety. This is also an important issue for buildings in
Oregon due...
The objective of this study was to develop and validate practical modeling
methods for investigating load paths and system behavior in a realistic, light-frame wood
structure. The modeling methods were validated against full-scale tests on subassemblies
and an L-shaped house. The model of the L-shaped house was then modified
and...
There are about 80 million single-family dwellings (SFD) in the United States, predominantly of wood-frame construction. Of these, 68% are owner occupied. A home is typically the largest single investment of a family, and is often not covered by earthquake insurance, even where it is available. Of all SFD in...
Many nondestructive techniques for structural health monitoring are subjective and based on visual observations of degradation. In addition, dynamic properties of structures are already used to obtain quantitative structural health data. However, most current data collection is limited to localized damage on the structure, rather than global response. Recent research...
Mass timber is emerging as a viable form of construction around the world in new markets for wood buildings. The entrance into these markets has driven the demand for more knowledge to enable designs alongside other structural materials such as steel and reinforced concrete.
Large, in-plane tests on cross-laminated timber...
