Search Constraints

Start Over
Filtering by: Has journal Wood Material Science & Engineering Remove constraint Has journal: Wood Material Science & Engineering Advisor Gupta, Rakesh Remove constraint Advisor: Gupta, Rakesh Degree Level Master's Remove constraint Degree Level: Master's

Search Results

  • Monotonic and Cyclic Testing of Cross-Laminated Timber Diaphragms

    Creator:
    Beairsto, Cody J.
    Abstract:
    Mass timber is emerging as a viable form of construction around the world in new markets for wood buildings. The entrance into these markets has driven the demand for more knowledge to enable designs alongside other structural materials such as steel and reinforced concrete. Large, in-plane tests on cross-laminated timber...
    Resource Type:
    Masters Thesis
    Full Text:
    in Civil Engineering and Wood Science presented on June 19, 2020 Title: Monotonic and Cyclic

  • Load Path Investigation in a Light-Frame Wood House with Complex Geometry

    Creator:
    Holman, Justin D.
    Abstract:
    The objective of this study was to investigate load paths in an existing light-frame wood structure with complex geometry, using previously established computer modeling methods. The structural model is derived from an existing, multi-level residence located in Corvallis, Oregon. For the purpose of this study, the existing structure was simplified...
    Resource Type:
    Masters Thesis
    Full Text:
    . Holman for the degree of Master of Science in Civil Engineering and Wood Science and presented on

  • Behavior of Cross-Laminated Timber Diaphragm Panel-to-Panel Connections with Self-Tapping Screws

    Creator:
    Sullivan, Kyle
    Abstract:
    The goal of this project is to contribute to the development of design values for cross-laminated timber (CLT) diaphragms in the seismic load-resisting system for buildings. Monotonic and cyclic tests to determine strength and stiffness characteristics of 2.44 m (8 ft) long shear connections with common self-tapping screws were performed....
    Resource Type:
    Masters Thesis
    Full Text:
    _____________________________________________________________________ Head of the Department of Wood Science and Engineering

  • Lateral Load Path Analysis : Practical Methods for Light-Frame Modular Structures

    Creator:
    Huynh, Thanh Q.
    Abstract:
    The objectives of this study are to use SAP2000 to investigate lateral load paths and system behavior in a modular, light-frame wood structure by investigating different foundation configurations and to further develop and validate existing modeling techniques of shear wall elements based on the Perforated Shear Wall Method. The modeling...
    Resource Type:
    Masters Thesis
    Full Text:
    Professor representing Wood Science Co-Major Professor representing Civil Engineering Head

  • Use of Virtual Visual Sensors in the Determination of Natural Frequencies of Timber Structures for Structural Health Monitoring

    Creator:
    Walker, Kristopher
    Abstract:
    Many nondestructive techniques for structural health monitoring are subjective and based on visual observations of degradation. In addition, dynamic properties of structures are already used to obtain quantitative structural health data. However, most current data collection is limited to localized damage on the structure, rather than global response. Recent research...
    Resource Type:
    Masters Thesis
    Full Text:
    Kristopher Walker for the degree of Master of Science in Civil Engineering and Wood Science presented on

  • Light-frame versus timber frame : a study in quantifying the differences

    Creator:
    Malone, Brian P.
    Abstract:
    The objective of this study was to compare light wood framing and traditional timber framing quantitatively through environmental impact assessment and load path analysis. This research was inspired by a traditional timber frame structure constructed in Vermont in 2011, and the design of structures considered within reflect the general characteristics...
    Resource Type:
    Masters Thesis
    Full Text:
    . APPROVED: Co-Major Professor representing Wood Science and Engineering Co-Major

  • Practical modeling for load paths in a realistic, light-frame wood house

    Creator:
    Pfretzschner, Kathryn S.
    Abstract:
    The objective of this study was to develop and validate practical modeling methods for investigating load paths and system behavior in a realistic, light-frame wood structure. The modeling methods were validated against full-scale tests on subassemblies and an L-shaped house. The model of the L-shaped house was then modified and...
    Resource Type:
    Masters Thesis
    Full Text:
    Wood Science and Civil Engineering presented on September 5, 2012   Title: Practical Modeling for

  • Evaluation of remediation techniques for circular holes in the webs of wood I-joists

    Creator:
    Polocoser, Tiberiu
    Abstract:
    The objective of this project was to evaluate methods to remediate a wood I-joist with a single, circular hole in the web while leaving utilities in place. The methods were experimentally evaluated with a full-scale bending test using four equally spaced point loads. There were three depths of joists with...
    Resource Type:
    Masters Thesis
    Full Text:
    POLOCOSER for the degree of Master of Science in Wood Science and Civil Engineering presented on 12 June

  • Optimizing the performance of gypsum wall board in wood frame shear walls

    Creator:
    Goodall, Scott I.
    Abstract:
    The overall goal of this project was to design a wood frame shear wall that could withstand greater displacement before damage occurred to the Gypsum Wall Board (GWB). More specifically, the objectives of the study were: (1) to evaluate damage to the GWB in alternative shear wall designs at 1%,...
    Resource Type:
    Masters Thesis
    Full Text:
    the degree of Master of Science in Civil Engineering and Wood Science presented on March 8, 2010

  • Evaluation of system effects and structural load paths in a wood-framed structure

    Creator:
    Martin, Kenneth G.
    Abstract:
    The objective of this project was to develop an analytical model of a light-framed wood structure using a prevalent structural analysis computer program in order to evaluate system effects and define load paths within the structure, especially under extreme wind events. Simplified modeling techniques and material definitions were developed and...
    Resource Type:
    Masters Thesis
    Full Text:
    degree of Master of Science in Civil Engineering and Wood Science presented on January 29, 2010