Index Catalog // ScholarsArchive@OSU

The design of a mechanism for tensile testing in a liquid helium Dewar

Creator:: Fullman, Carl Harvey
Resource Type:: Masters Thesis
Full Text:: the School of Mechanical Enineerinf2 for their much needed assistance and eseciaily to Professor R

An experimental investigation of combustion products through a flat, laminar, pre-mixed hydrocarbon-air flame

Creator:: Brenchley, David Lee
Abstract:: Flat, laminar, premixed hydrocarbon-air flames were stabilized on a porous-plate burner. In addition to temperature profiles, concentration profiles were measured for methane, ethane, ethylene, propane, acetylene, propylene, carbon monoxide, carbon dioxide and oxides of nitrogen. Dead space thickness, luminous flame zone thickness and hydrocarbon disappearance point responses were also monitored....
Resource Type:: Dissertation
Full Text:: BRENCHLEY for the Ph. D. (Name) (Degree) in MECHANICAL ENGINEERING presented on ` % /' C j j ,i

The conversion of solar radiation to heat energy using a trough-type parabolic mirror

Creator:: Mackie, Keith Leroy
Resource Type:: Masters Thesis
Full Text:: surface depends upon how much dust, ozone, water vapor and air it must D I R E C T S O L A R R A D

Some factors affecting the heat transfer in a finned tube radiator using low pressure steam and hot water as a heat source

Creator:: Waterhouse, Alvin Sidney
Resource Type:: Masters Thesis
Full Text:: requirements for the degree of MASTER OF SCIENCE June 1960 APPROVED: Professo r of Mechanical

Catastrophic propagation of ductile cracks in metallic foils

Creator:: Elliott, Leonard Thomas
Abstract:: The sudden failure of metal structures under load, which has been a design problem for many years, is characterized by a crack propagation rate which approaches the speed of sound in the material. These failures, which are often known as catastrophic fractures, may be divided into two types which depend...
Resource Type:: Masters Thesis
Full Text:: ACKNOWLEDGEMENTS The author wishes to e>qpress his appreciation and gratitude to Professor R. D. Olleman of the

Effects of selected minor alloying additions on the structure deformation characteristics of beryllium

Creator:: Dooley, George Joseph, III
Abstract:: Solid solution alloying was employed in an attempt to produce some relatively ductile form of beryllium. If the c/a ratio could be significantly altered, it was felt new or different slip systems could be activated. The following elements were selected on the basis of atomic size, melting point, crystal structure...
Resource Type:: Dissertation
Full Text:: of this orientation f, the r + {ow} A D B C E FIGURE 2. Important planes and

The use of a Stirling hot-air engine in converting solar energy to mechanical power

Creator:: Boehme, Martin Leon
Resource Type:: Masters Thesis
Full Text:: sincerely grateful to Professor Arthur D. Hughes of the Department of' Mecharical Enineerin for his

Control of peak stresses in tensile testing machine components subjected to shock loading

Creator:: Mitchell, Jack Alan
Abstract:: The mechanical properties of materials at cryogenic temperatures have been the subject of increasing interest during the past few years, although very little actual materials testing has been done at extremely low temperatures because of the high cost and low heat of vaporaization of liquid helium. Recently, the Department of...
Resource Type:: Masters Thesis
Full Text:: = 0 dx d t2 + ß2S = 0 The general solution to the first equation can be written as: and R(x

Indentation hardness of Douglas fir and Western hemlock lumber related to density

Creator:: Corder, Stanley E.
Abstract:: Indentation hardness tests were made on sections of 211 pieces of Douglas fir and 208 pieces of Western hemlock at a moisture content of about 11 percent. Specific gravity and visual-density evaluations were also determined. Correlation coefficients for linear regression of density, as measured by specific gravity, on average standard...
Resource Type:: Masters Thesis
Full Text:: approved William D. McMullen Indentation hardness tests were made on sections of 211 pieces of Douglas

The effect of entrance configuration on local heat transfer coefficients in subsonic diffusers

Creator:: Stoffel, Edward Oswald
Abstract:: The effects of round, square, and reentrant entrances on flow regimes and local heat transfer coefficients were determined using a symmetrical, plane-wall two-dimensional, subsonic air diffuser with one of the diverging walls heated and maintained isothermal. Flow and heat transfer studies were made at total divergence angles ranging from 0...
Resource Type:: Masters Thesis
Full Text:: entrance. (43, p. 391), / - ' ._ - d r i 8 5 The stall is generally first seen in a corner

ScholarsArchive@OSU

The design of a mechanism for tensile testing in a liquid helium Dewar

An experimental investigation of combustion products through a flat, laminar, pre-mixed hydrocarbon-air flame

The conversion of solar radiation to heat energy using a trough-type parabolic mirror

Some factors affecting the heat transfer in a finned tube radiator using low pressure steam and hot water as a heat source

Catastrophic propagation of ductile cracks in metallic foils

Effects of selected minor alloying additions on the structure deformation characteristics of beryllium

The use of a Stirling hot-air engine in converting solar energy to mechanical power

Control of peak stresses in tensile testing machine components subjected to shock loading

Indentation hardness of Douglas fir and Western hemlock lumber related to density

The effect of entrance configuration on local heat transfer coefficients in subsonic diffusers

Limit your search

Academic Affiliation

Advisor

Commencement Year

Committee Member

Creator

Date

Decade

Degree Field

Degree Level

Degree Name

Language

Non-Academic Affiliation

Peer Reviewed

Resource Type

Rights Statement

Subject

Search Constraints

Search Results

Limit your search