Index Catalog // ScholarsArchive@OSU

Creator:: Ericksen, Wilhelm S. and Forest Products Laboratory (U.S.)
Abstract:: This report is one of a series issued in cooperation with the Air Force-Navy-Civil Subcommittee on Aircraft Design Criteria under the supervision of the Aircraft Committee of the Munitions Board. Information reviewed and reaffirmed 1960. Revised June 1953.
Resource Type:: Technical Report
Full Text:: Wisconsin THE BENDING OF A CIRCULAR SANDWICH 1 2PANEL UNDER NORMAL LOAD— By WILHELM S ERICKSEN

Creator:: Ramos, Agustin N., Jr. and Forest Products Laboratory (U.S.)
Abstract:: A method is described to determine the distribution of the bending stresses in a wood beam when some of these stresses exceed the proportional limit. This is used to calculate the position of the neutral axis and the bending strength of some Douglas-fir beams. The calculated values agreed with the...
Resource Type:: Technical Report
Full Text:: determine the distribution of the bending stresses in a wood beam when some of these stresses exceed the

Creator:: Forest Products Laboratory (U.S.) and Ramos, Agustin N., Jr.
Resource Type:: Technical Report
Full Text:: determine the distribution of the bending stresses in a wood beam when some of these stresses exceed the

Creator:: Smith, C. B., Heebink, T. B. (Thomas Bruce), 1914-, Norris, Charles, B. (Charles Brazer), 1894-, and Forest Products Laboratory (U.S.)
Abstract:: Information reviewed and reaffirmed March 1956 and 1962. Original report published 1946.
Resource Type:: Technical Report
Full Text:: This report presents a mathematical analysis of the effective stiffness of a stiffener attached to a

Creator:: Lewis, Wayne C., 1914- and Forest Products Laboratory (U.S.)
Abstract:: This report is one of a series issued in cooperation with the ANC-23 Panel on Sandwich Construction of the Departments of the Air Force, Navy, and Commerce. Information reviewed and reaffirmed 1962. Original report issued December 1956.
Resource Type:: Technical Report
Full Text:: veri- fication of the mathematical derivations presented in Report 1847. Panels 20 by 20 and 20 by 30

Creator:: Forest Products Laboratory (U.S.) and Raville, Milton E.
Abstract:: This report is one of a series issued in cooperation with the ANC-23 Panel on Sandwich Construction of the Departments of the Air Force, Navy, and Commerce. Information reviewed and reaffirmed September 1962. Original report dated December 1955.
Resource Type:: Technical Report
Full Text:: lower facing bending moments and twisting moment per unit length of upper facing bending moments and

Creator:: Raville, Milton E. and Forest Products Laboratory (U.S.)
Abstract:: This report is one of a series issued in cooperation with the Air Force-Navy-Civil Subcommittee on Aircraft Design Criteria under the supervision of the Aircraft Committee of the Munitions Board.
Resource Type:: Technical Report
Full Text:: thickness. This requires that the bending moment and the transverse shear in the individual facings be

Creator:: Forest Products Laboratory (U.S.), Norris, Charles, B. (Charles Brazer), 1894-, Ericksen, Wilhelm S., March, H. W., Smith, C. B., and Boller, Kenneth H.
Abstract:: Information reviewed and reaffirmed April 1961. Previous report dated November 1949.
Resource Type:: Technical Report
Full Text:: divided into three parts. Part I contains the mathematical analysis. It makes use of the simplifying

Creator:: Norris, Charles, B. (Charles Brazer), 1894- and Forest Products Laboratory (U.S.)
Abstract:: Information reviewed and reaffirmed May 1962. Results here reported were obtained during 1950.
Resource Type:: Technical Report
Full Text:: the formula, and good agreement is found. Mathematical Development The General Henky-von Mises

Creator:: Forest Products Laboratory (U.S.) and Kuebler, Hans
Resource Type:: Technical Report
Full Text:: stresses in the veneers are added algebraically to the bending stresses and increase or decrease the total

ScholarsArchive@OSU