Formula Student challenges collegiate teams around the world to compete against one another in global racing competitions. Global Formula Racing (GFR) is a collaboration between Oregon State University and German at Duale Hochshule Baden- Wurttemberg Ravensburg students to build a racecar. The task assigned was to create a pedal assembly...
The purpose of this project is to examine the effect of the slot gap spacing on a multi element rear
wing. A three element rear wing is used in order to produce maximum downforce at the relatively
low speed of Formula SAE competitions. These high lift configurations serve to increase...
A new technique is developed to recover elemental tellurium (Te) from cadmium telluride (CdTe) which is abundantly available in photovoltaic semiconductor waste. The method is based on microchannel fluid flow with the use of a supported liquid membrane (SLM) between the donor (feed) and acceptor (strip) channels. A predictive theoretical...
The ATRIAS agile humanoid robot, along with a number of other spring-mass walking
machines, currently have two instabilities: one resulting from inertial forces on the torso
which cause the robot to spin like a top, and another resulting from stiff ground collisions
which cause chattering of the point-contact toes. This...
Infrastructure systems are a critical component supporting today's modern society. From
power grids to traffic networks, we rely on these systems to perform as intended, despite
the various sources of uncertainty present in their operation. Designing for system
robustness can help mitigate the impact of failures caused by unexpected events....
Excessive environmental vibrations can have deleterious effects in a variety of animals. Despite the potentially detrimental effects vibrations may have on animal health and experimental results, they remain poorly understood in the animal laboratory setting. This study investigates the consequences of excessive train vibrations on the breeding success of laboratory...
An experimental framework for investigation of the effects of Micro Pin Fin Arrays (MPFA) on the fuel oxidation efficiency of catalytic combustion is presented in this thesis. Complete combustion of the fuel is essential for operation at maximum efficiency and high standards of environmental cleanliness desired in existing microscale combustion...
Modern electronics have created increased demand for innovative cooling solutions. Typical forced convective cooling systems consist of pumps that circulate cooling fluid. However pumps can be unwieldy for many applications. This research is a continuation of work done at Oregon State University and Auburn University on the passive pumping of...
Robots are being utilized in ever more complex tasks and environments to help humans with difficult or dangerous tasks. However, robotic grasping is still in its infancy and is one of the limiting factors which prevent the deployment of robots in the home and other assisted living scenarios. Traditional methods...
Tensegrity structures are composed of pure compressional elements that are connected via a network of pure tensional elements. The concept of tensegrity promises numerous advantages to the field of robotics. Tensegrity robots are, however, notoriously difficult to control due to their oscillatory nature and nonlinear interaction between the components. Multiagent...
Current product design methodologies are not conducive to creating inclusive products (products that meet the needs of persons with and without disabilities). In order to reduce the effort and expense involved in creating inclusive products, empathic design principles are applied to discover whether customer needs for people with disabilities can...
The Oregon State University chapter of American Institute of Astronautics and Aeronautics competed in the Design/Build/Fly competition for the second time during the 2013/2014 school year. This chapter began at Oregon State in 2012 and still lacks an organized management system for the Design/Build/Fly team that could allow OSU to...
Multiagent learning with cooperative coevolutionary algorithms is a critical area of research, and is relevant to many real-world applications including air traffic control, distributed sensor network control, and game-theoretic applications such as border patrol. A key difficulty in multiagent learning is the credit assignment problem, where the impact of each...
Physical testing of composite sandwich panels in three point bending is an increasingly important aspect of qualifying a composite monocoque for Formula SAE competition. Required stiffness and strength values have increased over the past three years, and more of the monocoque's laminates must be tested as well. As a result,...
For many years, engine overhearing has been the major cause for vehicle breakdowns and engine malfunctions for most teams in Endurance events at Formula Society of Automotive Engineers (FSAE) Series competitions. Additionally, with a growing importance of aerodynamics to the overall success of the Global Formula Racing at these events,...
Every Spring and Summer, thousands of climbers attempt to summit Mt. Rainier. Many of them stop at Camp Muir, a base camp at 10,000 feet, where they can use restrooms, camp overnight, or refill water bottles before continuing their climb. Camp Muir currently uses a gas system to melt snow...
As the negative impacts of a fossil fueled electricity market are becoming more prevalent and destructive, the necessity for alternative energy techniques increases as well. However, before commercial implementation is underway, these alternatives must be assessed from three important perspectives: environmentally, economically, and socially, which are known as the three...
Extensive research has been conducted to improve the menus that allow navigation of digital world, most of it focused on the most common varieties of menu. Radial menus, a less common menu variety designed so that menu entries are aligned on a polar coordinate system, have largely been ignored. Early...
Since the 1970s, tendon-transfer surgeries have been routinely performed for a variety of conditions such as stroke, paralysis, spinal atrophy, trauma, and birth defects. The surgery involves rerouting a tendon from a disabled muscle and directly suturing it to a functioning muscle in order to partially restore hand function. This...
A combined experimental and computational fluid dynamics (CFD) study of single-phase liquid nitrogen flow through a microscale pin-fin heat sink is presented. Such cryogenic heat sinks could find use in applications such as high performance computing, spacecraft thermal management, and hydrogen storage thermal management. A circular pin fin heat sink...
During spring and early summer hydropower projects are often forced to spill water through their spillways due to increased river flows of the runoff season. Flows which are directed through spillways--instead of through turbines--contain a substantial amount of energy. Stemming from the high energy content, spillway flows entrain air at...
The research presented in this thesis is a continuation of collaboration between Oregon State University and Auburn University studying the feasibility of passively pumping liquid during boiling in a preferential direction using meso-scaled asymmetric surface patterns. Such a passive phase-change mechanism has great potential for thermal management in spacecraft and...
Practical bipedal robots need to be simultaneously efficient, robust, and versatile machines, but designing robots dynamically capable of these demands has been a significant bottleneck. We designed ATRIAS to be a highly dynamic biped capable of both walking and running untethered in real environments. To meet these goals, ATRIAS is...
A novel microscale combustor-heat exchanger (μCHX) for hydrogen storage applications is presented in this dissertation. The design of the μCHX is motivated by its application to two particular systems for automotive use- those that utilize metal hydrides (MH) and cryo-adsorbents (CA) to store hydrogen. Thermal energy needs to be supplied...
Whale blubber is the insular tissue layer located between the dermis and the superficial fascia layer which sheathes the whale's musculature. It is made up of a lipid matrix ramified with strong, structural collagen and elastic fiber bundles, but little is known of its mechanical properties. Knowing these properties adds...
Over 54 million people report having disabilities in the United States. In addition, there are 40.3 million people 65 years and older living in America. As the population continues to live longer and problems with obesity continue to increase, the number of people with limited capabilities will escalate as well....
Understanding the behavior of hydrophobic membranes is important for applications where separating a gas from a liquid-gas mixture is beneficial. For example, in-situ vapor extraction can be used in microscale heat sinks to improve heat transfer and flow stability. In this study, gas is experimentally evaluated flowing through flexible polytetrafluoroethylene...
The objective of this project is to demonstrate the feasibility fiber-reinforced turbine components through a design and manufacturing study. The motivation for using composites is to reduce weight and simplify manufacturing especially at high production volumes. In addition, natural fiber composites are implemented for applicable components to reduce environmental impact....
Predominant models for predicting rates of sediment transport face acute shortcomings when applied to coastal boundary layers. This is due to a neglect of the web of stochastic variables governing the rate of sediment dislodgement. While stochastic models do exist, the parametric extent of their validity tends to be limited,...
Development of micro air vehicles has led to a strong interest in the biomechanics of flapping fliers such as bats, birds, and insects, due to their ability to perform extreme unsteady maneuvers and fly in confined spaces. Determining the methods and mechanisms used by these fliers is a valuable source...
Identifying material characteristics of composites is important in designing any
structural system. The aerospace industry relies on these material properties not only to
design a functional aircraft, but also a safe and reliable one. Since carbon fiber
composites are relatively new materials, little is known about its characteristics under
certain...
The use of adhesives in demanding engineering applications is a very common
occurrence in the modern world. These adhesives are taking the role of many traditional
fasteners, especially in the area of fiber reinforced composites. As the use of these
adhesives become more common place, better understanding of their mechanics...
This thesis is the result of two research publications, which together form a framework for the evaluation of product innovativeness with potential future applications to early design. Innovation is a challenging concept to quantify. Experts seemingly have a grasp of what innovation is when they see it, however this evaluation...
Hydraulic power take-off (PTO) systems have been implemented in several wave energy converter (WEC) designs in recent years. Two popular hydraulic PTO configurations coupled to a point absorber hydrodynamic model are simulated in waves representative of an energetic sea state likely to be found in deep waters off the coast...
Presented is an investigation into the modeling, active control design, and simulation of a generic horizontal pendulum wave energy converter, known as a PWEC. A description is provided of the dominant attributes PWECs have, showcasing their promising potential as wave energy converters. Seeking to further promote this potential, an active...
A student-built lap time simulation coupled with the scoring model of the Formula Society of Automotive Engineers (SAE) Series has revealed the major importance of downforce on overall points. As a result, the Global Formula Racing (GFR) team has recently focused much effort towards the development of an aerodynamics package...
The Design/Build/Fly competition (DBF) is an annual aerospace engineering competition hosted by the American Institute of Aeronautics and Astronautics (AIAA). Oregon State University's AIAA chapter competed for the first time at DBF in 2013 and finished in the top 25% which is a respectable finish for a first year team....
This thesis serves as a literature review of dashboards that calls for further research in the area of Feedback Mechanisms (FMs). A dashboard, for the purposes of this paper is a display used to provide performance feedback to a user. An FM is the mechanism used in a dashboard to...
Advances in electronics fabrication, coupled with the demand for increased computing power, have driven the demand for innovative cooling solutions to dissipate waste heat generated by these devices. To meet future demands, research and development has focused on robust two-phase heat transfer devices. A confined impinging jet is explored as...
The properties of (1-x)BaTiO3-xBi(Mg1/2Ti1/2)O3 (BT-BMT) ceramics were fabricated from reagent-grade ceramic powders by solid-state methods and investigated for solubility, relative permittivity, dielectric loss, polarization, and electromechanical strain. The solubility limit was found to be between x = 0.3 and 0.4. Ba-deficient samples were fabricated, corresponding to stable single-phase compositions; these...
This thesis consists of two papers in manuscript format. The first paper presents optical measurements of tsunami inundation through an urban waterfront in a laboratory wave basin. The physical model was constructed at 1:50 scale and was an idealization of the town of Seaside, Oregon. The paper presents an analysis...
Innovation is a key element for a product to achieve market success, but identifying it within product or even defining the term is a difficult task. Identifying innovation has been approached in many different ways. Experts in design engineering may identify innovative designs based on an analysis of a product's...
An open area of research in complex systems is to move reliability and failure assessments earlier in the engineering design process. When compared to later design, early decisions are cost effective and have a large impact on the system. Standard methods are limited by the availability of data and often...
We seek the control strategies that are applicable on legged robots and control them to run in real world as robust and efficient as animals. To achieve this goal, we need to understand the principles of legged locomotion and the control policies that animals use during running. In this study...
Recent advances in multiagent learning have led to exciting new capabilities spanning fields as diverse as planetary exploration, air traffic control, military reconnaissance, and airport security. Such algorithms provide a tangible benefit over traditional control algorithms in that they allow fast responses, adapt to dynamic environments, and generally scale well....
In this work, flow through synthetic arrangements of contacting spheres is studied
as a model problem for porous media and packed bed type flows. Direct numerical
simulations are performed for moderate pore Reynolds numbers in the range,
10 ≤ Re ≤ 600, where non-linear porescale flow features are known to...
In-situ vapor extraction is performed by applying a pressure differential across a hydrophobic porous membrane that forms a wall of the channel as a means of reducing the local quality of flow boiling within the channel. As the local quality is reduced, the heat transfer capability can be improve while...
Lead zirconate titanate (PZT) is well known to exhibit some of the strongest piezoelectric responses, explaining why it is at the heart of piezoelectric-based microelectromechanical systems (MEMS) research. The use of pulsed laser deposition (PLD) to synthesize PZT offers many advantages over alternative deposition techniques, mainly regarding its ability to...
The population of minority groups is on the rise in the US, yet still minorities are not proportionally represented in Science, Technology, Engineering, and Mathematics (STEM). Of these minorities there are 4 races/ethnicities that are vastly under represented: Blacks, Hispanics, American Indians/Native Alaskans, and Hawaiians/Pacific Islanders. For the US to...
In this dissertation, a group of vehicle dynamics simulation tools is developed with two primary goals: to accurately represent vehicle behavior and to provide insight that improves the understanding of vehicle performance. Three tools are developed that focus on tire modeling, vehicle modeling and lap time simulation.
Tire modeling is...
With continued development of the electronic industry, the demand for highly efficient heat removal solutions requires innovative cooling technologies. A computational fluid dynamic (CFD) study, including heat transfer, is performed for an axisymmetric, confined jet impingement experiencing boiling and coupled with vapor extraction. Boiling occurs at the target surface while...
Porous media flows are encountered in many natural and man-made systems such as gas adsorption, filtration, heat exchangers, combustion, catalytic reactors and groundwater hydrology. This study experimentally investigates these flows as function of pore Reynolds number, Re[subscript pore]. The pore Reynolds number is based on the porous bed hydraulic diameter,...
Understanding the mechanical behavior of composite materials requires extensive knowledge of fracture behavior as a crack approaches an interface between the bulk material and the reinforcement structure. Overall material toughness can be greatly influenced by the propensity of an impinging crack to propagate directly through the substrate or deflect along...
Among the many safety hazards facing chainsaw operators, the phenomenon known as kickback is the most dangerous. Kickback occurs when the chain at the tip of the chainsaw is caused to stop abruptly, and transfers the energy of the cutting chain to motion of the saw. The saw will rotate...
When using Finite Element Analysis (FEA) to model notched composite panels, the values of certain material properties can have a great effect on the outcome of the simulation. Progressive damage modeling is used to model how a composite structure will fail, and how that failure will affect the response of...
Characterization of local boiling trends, in addition to the typically reported area-averaged trends, is essential for the robust design and implementation of phase change technologies to sensitive heat transfer applications such as electronics cooling. Obtaining the values of heat fluxes corresponding to locally varying surface temperatures has been a challenge...
There are many options available when selecting a computational model for
two-phase flows. It is important to understand all the features of the model
selected, including when the model is appropriate and how using it may affect
your results. This work examines how volume displacement effects in two-phase
Eulerian-Lagrangian models...
A lightweight carbon fiber reinforced polymer (CFRP) c-channel beam was previously designed using analytical theory and finite element analysis and subsequently manufactured through a pultrusion process. Physical testing revealed the prototype did not meet the bending and torsional stiffness of the beam model. An investigation revealed that the manufactured prototype...
This work proposes a framework of concept generation and evaluation that takes into consideration the benefit of creativity and innovation in current market trends. By educating engineers in how to increase creativity in concept design and assess it quantitatively, the next generation of designers will be a step ahead of...
The problem of determining whether a crack impinging on an interface will penetrate into the substrate or deflect along the interface is vital to the effective design of layered and composite material systems. Of particular interest is the transition between crack propagation by penetration through an interface and deflection along...
Natural stream systems contain a variety of flow geometries which contain flow separation, turbulent shear layers, and recirculation zones. This work focuses on streams with dead zones. Characterized by slower flow and recirculation, dead zones are naturally occurring cutouts in stream banks. These dead zones play an important role in...
Recent work has shown humanoid robots with spinal columns, instead of rigid torsos, benefit from both better balance and an increased ability to absorb external impact. Similarly, snake robots have shown promise as a viable option for exploration in confined spaces with limited human access, such as during power plant...
Identifying material parameters in composite plates is a necessary first step in a variety of structural applications. For example, understanding the material parameters of carbon fiber composite is important in investigating sensor and actuator placement on micro-air-vehicle wings for control and wing morphing purposes. Knowing the material parameters can also...
While many organizations claim to "put safety first," safety is rarely considered early in the design process when system-level architectural decisions are made. Instead, system design follows an abstraction-to-detail process to first meet functional and then performance requirements. Following this process, safety assurance occurs in the later stages of design...
A gap exists in the methods used in industry and available in academia that prevents customers and engineers from having a voice when considering engineering risk appetite in the dynamic shaping of early-phase conceptual design trade study outcomes. Current methods used in Collaborative Design Centers either collect risk information after...
In this work we present a multiagent Fleet Coordination Problem (FCP). In this formulation, agents seek to minimize the fuel consumed to complete all deliveries while maintaining acceptable on-time delivery performance. Individual vehicles must both (i) bid on the rights to deliver a load of goods from origin to destination...
Engineers have long been inspired by nature's flyers. Such animals navigate complex environments gracefully and efficiently by using a variety of evolutionary adaptations for high-performance flight. Biologists have discovered a variety of sensory adaptations that provide flow state feedback and allow flying animals to feel their way through flight. A...
This paper combines two research publications working toward the development of an integrated framework for commercial sustainable building design. Current methodologies utilize a traditional architectural top-down approach to sustainable building design practices that consumes financial and temporal resources early in the design process. By identifying the array mechanical subsystems required...
Several standardized courses for Formula SAE (FSAE) testing are introduced and described with sufficient detail to be reproduced by any Formula SAE team. Basic analysis methods for the courses are given as well as explanations of how those analyses could be used. On-car data from the Global Formula Racing (GFR)...
For robotic manipulation tasks in uncertain environments, research typically revolves around developing the best possible software control strategy. However, the passive dynamics of the mechanical system, including inertia, stiffness, damping and torque limits, often impose performance limitations that cannot be overcome with software control. Discussions about the passive dynamics are...
Current life cycle assessment tools are often deficient in assisting design for sustainable manufacturing efforts. Integrating an improved assessment method into a decision support framework will provide a means for designers and engineers to better understand the impacts of their decisions. A unit process modeling-based sustainability assessment method is presented...
What constitutes a quality solution to an authentic task from industry? This study seeks to address this question through the examination of two expert solutions to an authentic engineering task used in the Chemical, Biological and Environmental Engineering curriculum at Oregon State University. The two solutions were generated by two...
Wave Energy Converters (WECs) promise to be a viable alternative to current electrical generation methods. However, these WECs must become more efficient before wide-scale industrial use can become cost-effective. The efficiency of a WEC is primarily dependent upon its geometry and ballast configuration which are both difficult to evaluate, due...
The performance of a combined vapor-compression cycle/ORC is evaluated using waste-heat from a diesel generator. A flat plate microchannel heat exchanger is employed to provide energy exchange between the diesel exhaust stream and an oil loop, which provides energy to a boiler. This study finds an increased diesel duty corresponds...
Coordination is essential to achieving good performance in cooperative multiagent systems. To date, most work has focused on either implicit or explicit coordination mechanisms, while relatively little work has focused on the benefits of combining these two approaches. In this work we demonstrate that combining explicit and implicit mechanisms can...
Advances in electronics fabrication, coupled with the demand for increased computing power, have driven the demand for innovative cooling solutions to dissipate waste heat generated by these devices. To meet future demands, research and development has focused on robust and stable two-phase heat transfer devices. A confined impinging jet is...
As drop-on-demand (DOD) applications continue to gain ground in desktop inkjet-printing, 3D printing, fluid mixing, and other areas the demand for higher frequency operations are beginning to push against the current physical boundaries in DOD technology. The current research is exploring the possibility of controlling drop volume and velocity at...
Thermoelectric materials are playing an increasingly significant role in the global effort to develop sustainable energy technologies. Consequently, the demand for materials with greater thermoelectric efficiency has stimulated the development of state-of-the-art interstitially doped skutterudite-based materials. However, since intermetallics are often embrittled by interstitial substitution, optimal skutterudite-based device design, manufacture,...
A microchannel heat exchanger was designed for diesel waste heat recovery and its performance was evaluated. The 21x15x8 cm unit was constructed from diffusion brazed stainless steel lamina and weighed 11 kg. Operating from a 13.4 kW generator with an exhaust temperature of 500 °C the unit delivered 11.1 kW...
We present a novel control strategy for running which is robust to disturbances, and makes excellent use of passive dynamics for energy economy. The motivation for our control strategy is based on observations of animals, which are able to economically walk and run over varying terrain and ground dynamics. It...
Rising energy demands and the continual push to find more energy efficient technologies have been the impetus for the investigation of waste heat recovery techniques. Diesel engine exhaust heat utilization has the potential to significantly reduce the consumption of fossil fuels and reduce the release of greenhouse gases, because diesel...
This thesis is the summation of two publications with the motivation to move reliability analysis earlier in the design process. Current analyses aim to improve reliability after components have been selected. Moving specific analyses earlier in the design process reduces the cost to the designer. These early design analyses provide...
Technologies such as avionics and power electronics are driving the demand for thermal management schemes towards high heat fluxes and low surface temperatures. Typically, these applications require the dissipation of heat fluxes in the rage of 100-1000 W/cm² while maintaining surface temperatures lower than about 85 °C. Phase-change heat transfer...
A method was sought to predict the flight paths and collisions for closely spaced ink droplets of various sizes as a design aid for ink-jet printing development. Computational fluid dynamics models of two rigid aligned spheres, as a proxy for ink droplets, were initiated in atmospheric pressure air at constant...
A number of computational tools now exist to aid in developing conceptual solutions based on a functional description of a design problem. A key limitation of these tools is the way results are organized for presentation to the user. In general, results are an undifferentiated mass of potential solutions. Analysis...
This thesis investigates the applicability of the finite element method to model wave energy converter (WEC) hydroelasticity using LS-DYNA. The proposed methodology uses the Arbitrary Lagrangian-Eulerian formulation to model Fluid-Structure Interaction (FSI) between the WEC and the fluid elements. This formulation allows for time-domain modeling of higher order effects such...
While the locomotion performance of legged robots over flat terrain or known obstacles has improved over the past few decades, they have yet to equal the performance of their animal counterparts over variable terrain. This work analyzes a multi-legged reduced order model of cockroach locomotion on variable slopes which will...
Increasing access to modern forms of energy in developing countries is a
crucial component to eliminating extreme poverty around the world. Pico-hydro
schemes (less than 5-kW range) can provide environmentally sustainable electricity
and mechanical power to rural communities, generally more cost-effectively than
diesel/gasoline generators, wind turbines, or solar photovoltaic systems....
Future engineers need to be competitive in today's expanding global industries. They must have capabilities beyond standard engineering practice. In an attempt to develop students capable of working in a globally distributed design and manufacturing environment, Oregon State University (OSU) and Duale Hochschule Baden-Württemberg Ravensburg (DHBW) have developed a senior...
In cases where complex systems routinely experience extreme operating conditions, preventative maintenance is often employed to guard against system failure. Yet, with accessible real-time data and the standard practice becoming prohibitively expensive, the test stand can serve as a vital contributor to the development of system health and reliability estimations....
Experiments on a novel, microscale hydrogen combustor heat exchanger (µCHX) are presented in this thesis. The µCHX has been designed to efficiently transfer thermal energy to a heat transfer fluid for use in desorption of hydrogen from a metal hydride storage system of a hydrogen-powered fuel cell vehicle. The experimental...
This study is a comparison to establish similarities between the funding resources of college and university athletic bands. The secondary objective is to determine the funding potential that exists as a result of alumni relations. In order to obtain funding information for a variety of athletic band programs, a survey...
This thesis presents a feasibility study of a means to passively effect liquid motion parallel to a heated surface though surface geometrical modifications. Such a passive system is beneficial for electronics cooling applications as it reduces the pumping equipment normally required in flow loops and is desired for space applications,...
Wave energy conversion is still in its infancy, and in order for it to become a commercially viable technology, developers, investors and utilities need to estimate a Wave Energy Converter's (WEC's) performance for the wave climate of a potential installation site. With the goal of estimating a design's power output...
Computation of offset curves is an operation critical to many computer-aided design and manufacturing (CAD/CAM) applications. Though simple on the surface, differences between the straightforward mathematical definition and the demands of CAD/CAM environment in the formulation and expression of an offset curve create a problem for which only complicated, approximate...
Innovation can be considered the driving force behind product design. This thesis strives to improve the ease at which innovation is achieved. Firstly by examining how design information is presented and comprehended by various personality types. The Myers-Briggs Type Indicator test is a quick, easy, and accurate way to determine...
The intent of this paper is to bring more attention to the mastery involved with film composition as an art form. The research focuses specifically on the life, style, influences, and works of John Williams as a conductor, film composer, and composer. It addresses his biography, filmography, and working relationships,...
After traveling to Africa and experiencing the struggles and confusion of interacting with a new culture, I saw the need for some sort of orientation device that would adequately prepare first timers, but also not be too lengthy and daunting for a person that will only be spending a few...
Hot engine exhaust and industrial process exhaust represents a resource that is often rejected to the environment without further utilization. This resource is prevalent in the transportation and industrial process sectors, but stationary engine-generator systems also typically do not utilize this resource. Engine exhaust is considered high grade heat and...
Fractal-like branching microchannel flow networks have been found to improve wall temperature uniformity and decrease both pressure drop and flow power compared to arrays of straight microchannels. The present study seeks to maximize the benefits of fractal-like branching channels by means of a gradient-based optimization algorithm. The algorithm identifies the...