Search Constraints

Start Over
Filtering by: Creator Evans, T. Matthew Remove constraint Creator: Evans, T. Matthew Degree Field Mechanical Engineering Remove constraint Degree Field: Mechanical Engineering Rights Statement In Copyright Remove constraint Rights Statement: In Copyright

Search Results

  • Heat transfer during the piston-cylinder expansion of a gas

    Creator:
    Rodrigues, Matthew Jose
    Abstract:
    The expansion of a gas within a piston-cylinder arrangement is studied in order to obtain a better understanding of the heat transfer which occurs during this process. While the situation of heat transfer during the expansion of a gas has received considerable attention, the process is still not very well...
    Resource Type:
    Masters Thesis
    Full Text:
    AN ABSTRACT OF THE THESIS OF Matthew Jose Rodrigues for the degree of Master of Science in

  • Rapid Prototyping of Rigid & Flexible Microfluidic Devices Using Low-Cost Materials and Maker Tools

    Creator:
    Co, Megan T.
    Abstract:
    Microfluidics is an evolving field that focuses on the manipulation of small fluid volumes. Because of its micron-sized features, it is the basis for many lab-on-chip and point-of-care diagnostic devices. The devices are predominantly molded from polydimethylsiloxane (PDMS); however, production is a multi-hour or multi-day process that typically requires clean...
    Resource Type:
    Honors College Thesis
    Full Text:
    :_____________________________________________________ Matthew Johnston Microfluidics is an evolving field that focuses on the manipulation

  • Describing Tsunami Inundation and Debris Motion using Optical Measurement Methods in a Large-Scale Wave Basin

    Creator:
    Rueben, Matthew Robert
    Abstract:
    This thesis consists of two papers in manuscript format. The first paper presents optical measurements of tsunami inundation through an urban waterfront in a laboratory wave basin. The physical model was constructed at 1:50 scale and was an idealization of the town of Seaside, Oregon. The paper presents an analysis...
    Resource Type:
    Honors College Thesis
    Full Text:
    AN ABSTRACT OF THE THESIS OF Matthew

  • Automated Tradeoff Analysis of Cost Versus Machinability for Design Feedback

    Creator:
    Grier, Alan Thomas
    Abstract:
    As CAD tools become more sophisticated, engineers are able to more easily create complex part geometries with minimal mass given strength and stiffness requirements. However, these complex part geometries can be difficult to subtractively manufacture, which consequently increases manufacturing cost and production time. This thesis presents a method independent of...
    Resource Type:
    Masters Thesis
    Full Text:
    Analysis of Cost Versus Machinability for Design Feedback Abstract approved: Matthew I. Campbell As CAD

  • Automated Synthesis of Planar Mechanisms with Revolute, Prismatic and Pin-In-Slot Joints

    Creator:
    Huang, Weifeng
    Abstract:
    The intent of this research is to explore the entire design space of mechanism topologies by using a graph grammar synthesis approach. A new graph representation of planer mechanism has been developed to represent the planar mechanism with revolute (R), prismatic (P), and pin-in-slot (RP) joints. Following Gruebler's equation, the...
    Resource Type:
    Masters Thesis
    Full Text:
    : ______________________________________________________ Matthew I. Campbell The intent of this research is to explore the entire design space of

  • Automated Assembly Planning : From CAD Model to Virtual Assembly Process

    Creator:
    Rafibakhsh, Nima
    Abstract:
    Assembly planning is a crucial task for every manufacturing product. In general, assembly operations consume more than 30% of the total manufacturing time and cost. Therefore, any effort in optimizing assembly will have a significant impact on the economic success of manufacturing. Finding an optimal assembly plan by hand is...
    Resource Type:
    Dissertation
    Full Text:
    approved: ______________________________________________________ Matthew I. Campbell Assembly

  • Automated Design of Foam Packaging Shapes

    Creator:
    So, David M.
    Abstract:
    Creating effective packaging is about finding a balance between product protection during shipping and time consumption in the design process. Given time and cost constraints, it is hard to produce sufficiently protective padding while having it not be thicker than it needs to be. This thesis describes a method to...
    Resource Type:
    Masters Thesis
    Full Text:
    approved: _____________________________________________________ Matthew I. Campbell Creating

  • Design Automation for 3D Circuits

    Creator:
    Velayati, Mohammad
    Abstract:
    Traditional electronic systems are usually fabricated via printed circuit boards (PCBs). In a regular PCB, the electronic components are placed and mounted on a two-dimensional board. Such a component layout limits the freedom in the component placement process which results in larger electronic devices. With the use of Additive Manufacturing...
    Resource Type:
    Masters Thesis
    Full Text:
    : ______________________________________________________ Matthew I. Campbell Traditional electronic systems are usually fabricated via printed

  • Design automation for 3D circuits

    Creator:
    Velayati, Mohammad
    Abstract:
    Traditional electronic systems are usually fabricated via printed circuit boards (PCBs). In a regular PCB, the electronic components are placed and mounted on a two-dimensional board. Such a component layout limits the freedom in the component placement process which results in larger electronic devices. With the use of Additive Manufacturing...
    Resource Type:
    Masters Thesis
    Full Text:
    : ______________________________________________________ Matthew I. Campbell Traditional electronic systems are usually fabricated via printed

  • Applications of an Agent-Based Approach to Automated Structure Design

    Creator:
    Kiff, Robin E.
    Abstract:
    This thesis details the applications of a new method of agent-based structure synthesis. The goal of this research is to create structures that meet a structural goal within a simulated physics environment. The method proposed works as an iterative process of changing the structure, evaluating the new structure and using...
    Resource Type:
    Masters Thesis
    Full Text:
    : ______________________________________________________ Matthew I. Campbell This thesis details the applications of a new method of agent-based