Search Constraints

Start Over
Filtering by: Alternative title ssim ORESU-G-18-002 Remove constraint Alternative title ssim: ORESU-G-18-002 Degree Field Mechanical Engineering Remove constraint Degree Field: Mechanical Engineering

Search Results

  • Creep studies on Pheasant, Narcissus and Chukar aluminum conductors

    Creator:
    Patton, John Dennis
    Abstract:
    This thesis is an engineering report on the creep behavior of power transmission line conductors. Laboratory creep test results are reported for Pheasant, Narcissus and Chukar conductors. The report follows a standard nomenclature and format suggested by the International Study Committee No. 6 of Conference Internationale des Grands Reseaux Electriques...
    Resource Type:
    Masters Thesis
    Full Text:
    Engineering in (Material Science) presented on August 18, 1967 Title: CREEP STUDIES ON PHEASANT, NARCISSUS

  • A rapid method for determinations of nitrogen oxides in engine exhaust gas

    Creator:
    Johnson, Douglas Edward
    Resource Type:
    Masters Thesis
    Full Text:
    , 1956. 339p. 18. Wayne, L. G. and J. C. Romanovaky. Rates of reaction the oxides of nitrogen in photo

  • Thermal contact resistances in a thermal conductivity test system

    Creator:
    Schneider, Donald A.
    Abstract:
    The thermal contact conductance (TCC) between two machined pieces of stainless steel was studied. A guarded hot plate thermal conductivity test fixture was designed and built for the experiment. Factors investigated included the contact pressure, surface roughness, interface material and average test temperature. The contact pressure at the interface ranged...
    Resource Type:
    Masters Thesis
    Full Text:
    of Master of Science in Mechanical Engineering presented on August 18, 1998. Title: Thermal Contact

  • On the Role of Particle Size Distribution in Selective Laser Melting of 316L Stainless Steel

    Creator:
    Coe, Hannah G.
    Abstract:
    Selective laser melting (SLM) is an additive manufacturing (AM) process that uses a laser beam to melt metal powder as it is spread onto the build surface using a roller or scraper, followed by rapid solidification to manufacture a 3D component, one layer at a time. In SLM process, density...
    Resource Type:
    Masters Thesis
    Full Text:
    Hannah G. Coe March 18, 2019 All Rights Reserved

  • Dynamics and stability of lateral plane locomotion on variable inclines

    Creator:
    Bonnono, Scott A.
    Abstract:
    An actuated, bipedal model is developed to investigate lateral plane locomotion dynamics and stability on inclines. Both the point mass case and rigid body case are considered. Variations in the force-free leg length are determined via inverse dynamics to explicitly and implicitly match prescribed lateral and fore-aft force profiles, respectively....
    Resource Type:
    Masters Thesis
    Full Text:
    of Science in Mechanical Engineering presented on June 18, 2009. Title: Dynamics and Stability of

  • Flow characteristics of co-flowing, laminar streams in a rectangular microchannel

    Creator:
    Oak, Jason
    Abstract:
    The effects of varying flow rate ratio and Reynolds number on the momentum diffusion and flow development of two co-flowing, laminar streams in a rectangular microchannel are presented. The microchannel has an aspect ratio of approximately 16 with a width of 1006 μm and a height of 63 μm. A...
    Resource Type:
    Masters Thesis
    Full Text:
    Mechanical Engineering presented on July 18, 2001. Title: Flow Characteristics of Co-flowing. Laminar

  • Experimental investigation of natural convection from an array of uniformly heated horizontal cylinders to mercury

    Creator:
    Wang, Deing
    Abstract:
    An experimental investigation was conducted to better understand the heat transfer process with natural convection from an array of uniformly heated horizontal cylinders to mercury. Five assembly geometries were studied, these being the single horizontal cylinder, two cylinders with spacing ratios S/D = 2,3 and 4, (S represents the center-to-center...
    Resource Type:
    Dissertation
    Full Text:
    fufiliment of the requirements for the degree of DOCTOR OF PHILOSOPHY completed November 18 1986

  • Performance of rotary regenerative heat exchanger--a numerical simulation

    Creator:
    Bae, Young Lib
    Abstract:
    This thesis examines the transient and steady-state temperature performance of a rotary regenerative heat exchanger. In contrast to previous studies on this problem, fluid flow in the circumferential direction was considered. Appropriate modeling was included to measure the effect of carry-over on the differential equations describing mass and energy conservation....
    Resource Type:
    Dissertation
    Full Text:
    Mechanical Engineering presented on November 18, 1986. Title: Performance of a Rotating Regenerative Heat

  • Development of a meta-model for behavioral model representation and reuse

    Creator:
    Giles, Blake Jensen
    Abstract:
    Behavioral modeling is increasingly an imperative component of system design as the systems under construction become more and more complex. Without behavioral modeling available to the modern designer, design and verification of these systems would be much more laborious. Additionally, with the increasing computational power of today's modeling and simulation...
    Resource Type:
    Masters Thesis
    Full Text:
    !:;/:!<14?96M1!K891!/3G!!"!?/9!789!1Q/K@.1!;/4!/3!8J19/..! 7A3?:683! :8! :9/34@89:! @18@.1! 89

  • Modeling in-situ vapor extraction during flow boiling in microscale channel

    Creator:
    Salakij, Saran
    Abstract:
    In-situ vapor extraction is performed by applying a pressure differential across a hydrophobic porous membrane that forms a wall of the channel as a means of reducing the local quality of flow boiling within the channel. As the local quality is reduced, the heat transfer capability can be improve while...
    Resource Type:
    Dissertation
    Full Text:
    18 W, and extraction pressure differentials of 14 and 41 kPa, (b) inlet flow rate of 50 g/min, heat