Index Catalog // ScholarsArchive@OSU

Experimental combustion analysis and development of representative fuel specifications for selected wood and refuse derived fuel pellets from the Pacific Northwest

Creator:: Haluzak, Charles Craig
Abstract:: An experimental biomass combustion facility has been built and established at Oregon State University. The furnace, or Biomass Combustion Unit ( BCU ), uses an augertype fuel feed system, grate-type fuel support with under and over fire air supply. Fourteen pellet species from five States - Alaska, Washington, Oregon, Idaho,...
Resource Type:: Masters Thesis
Full Text:: burn wood biomass pellets under "reasonable" operating conditions and report the relative combustion

Water table analogue for compressible flow studies

Creator:: Pouderoux, Pierre
Resource Type:: Masters Thesis
Full Text:: "' - - _I ( u ;)u + V ~) · (8) ~ - s ~'/ 7:Jy d. Condition of Irrotationability By Kelvin's circulation

A dynamic procedure for evaluation resilient mountings

Creator:: Arents, Chester Abbo
Resource Type:: Masters Thesis
Full Text:: . . . . . . . . 15 V. D i s cus s i on . . . . . . . . . . . . . . . . . . . 1 8 Typical Commercial Mounting

Indentation hardness of Douglas fir and Western hemlock lumber related to density

Creator:: Corder, Stanley E.
Abstract:: Indentation hardness tests were made on sections of 211 pieces of Douglas fir and 208 pieces of Western hemlock at a moisture content of about 11 percent. Specific gravity and visual-density evaluations were also determined. Correlation coefficients for linear regression of density, as measured by specific gravity, on average standard...
Resource Type:: Masters Thesis
Full Text:: indenter loads of (A) 545 (maximum), (B) 200, (C) 100 and (D) 50 pounds. 21 8. Linear regression of

The method of characteristics for irrotational flow of a semi-perfect gas

Creator:: Rayl, Stephen Christopher
Resource Type:: Masters Thesis
Full Text:: Physical P1nes - II . . 25 7. InitIal Portion of Super8ontc Nozzle . 27 8. Hodo;raph and Physical

Measurement and scrubbing of SO₂ and NOx from boiler flue gases

Creator:: Reichel, Rolf Hubertus
Abstract:: At the Oregon State University heating plant the primary source of heat energy is natural gas with crude oil as the standby supply of fuel. In the future, as natural gas becomes a rarer commodity, more reliance will be placed on the use of the more expensive, more polluting, but...
Resource Type:: Masters Thesis
Full Text:: The author is deeply indebted to Professor A. D. Hughes for his significant help and encouragement

Effects of selected minor alloying additions on the structure deformation characteristics of beryllium

Creator:: Dooley, George Joseph, III
Abstract:: Solid solution alloying was employed in an attempt to produce some relatively ductile form of beryllium. If the c/a ratio could be significantly altered, it was felt new or different slip systems could be activated. The following elements were selected on the basis of atomic size, melting point, crystal structure...
Resource Type:: Dissertation
Full Text:: Abstract approved: William D. McMullen Solid solution alloying was employed in an attempt to produce

Exploring the Ductility Minimum of Niobium C103 at Intermediate Temperatures using Triaxial Tensile Specimens

Creator:: Wood, Thomas N., II
Abstract:: This work explores the mechanical properties of single-phase niobium alloy C103 from room temperature to 600°C for the purpose of expanding safe uses of the material into new applications. The study utilizes a symmetrically notched triaxial tensile specimens to manipulate the internal stress field in order to observe the changes...
Resource Type:: Masters Thesis
Full Text:: Julie D. Tucker This work explores the mechanical properties of single-phase niobium alloy C103

Control of peak stresses in tensile testing machine components subjected to shock loading

Creator:: Mitchell, Jack Alan
Abstract:: The mechanical properties of materials at cryogenic temperatures have been the subject of increasing interest during the past few years, although very little actual materials testing has been done at extremely low temperatures because of the high cost and low heat of vaporaization of liquid helium. Recently, the Department of...
Resource Type:: Masters Thesis
Full Text:: author would like to express his deep gratitude to Professor Roger D. 011eman of the Department of

The use of a Stirling hot-air engine in converting solar energy to mechanical power

Creator:: Boehme, Martin Leon
Resource Type:: Masters Thesis
Full Text:: lOO Io - - >- -80 (1) Zcr 9 - -fraction of lofai energy wo - -- 8 (D 7. 60 w z w 6

ScholarsArchive@OSU

Experimental combustion analysis and development of representative fuel specifications for selected wood and refuse derived fuel pellets from the Pacific Northwest

Water table analogue for compressible flow studies

A dynamic procedure for evaluation resilient mountings

Indentation hardness of Douglas fir and Western hemlock lumber related to density

The method of characteristics for irrotational flow of a semi-perfect gas

Measurement and scrubbing of SO₂ and NOx from boiler flue gases

Effects of selected minor alloying additions on the structure deformation characteristics of beryllium

Exploring the Ductility Minimum of Niobium C103 at Intermediate Temperatures using Triaxial Tensile Specimens

Control of peak stresses in tensile testing machine components subjected to shock loading

The use of a Stirling hot-air engine in converting solar energy to mechanical power

Limit your search

Academic Affiliation

Advisor

Commencement Year

Committee Member

Conference Name

Creator

Contributor

Date

Decade

Degree Field

Degree Level

Degree Name

File Format

Language

License

Location

Non-Academic Affiliation

Peer Reviewed

Resource Type

Rights Statement

Subject

Search Constraints

Search Results

Limit your search