Index Catalog // ScholarsArchive@OSU

Fluid forces on and flow configurations around a circular cylinder near a plane boundary

Creator:: Tavolacci, Don
Abstract:: The flow configurations around and the forces acting on a circular cylinder with its axis parallel to a nearby plane boundary and subjected to a uniform flow were investigated. The flow conditions, which were perpendicular to the cylinder axis and parallel to the plane boundary were investigated experimentally and theoretically....
Resource Type:: Masters Thesis
Full Text:: Fluid forces on and flow configurations around a circular

Boundary layer control tests by suction on a circular cyclinder wing section

Creator:: Dennon, Jack Dwight
Resource Type:: Masters Thesis
Full Text:: Boundary Layer Control Tests By Suction on a Circular

Laminar natural convection within long vertical uniformly heated parallel-plate channels and circular tubes

Creator:: Vorayos, Nat
Abstract:: The problem of simple mathematical models of laminar natural convective flow within a long vertical parallel-plate channels and circular tubes kept at uniformly heated walls is revisited to seek a clear physical understanding of heat transfer mechanisms. A series solution method to analyze the fully developed flow and an integral...
Resource Type:: Dissertation
Full Text:: heated parallel-plate channels and circular tubes AN ABSTRACT OF THE THESIS OF Nat Vorayos for the

Monte Carlo simulation of radiation heat transfer in a three-dimensional enclosure containing a circular cylinder

Creator:: Hong, Seung-Ho
Resource Type:: Masters Thesis
Full Text:: three-dimensional enclosure containing a circular cylinder AN ABSTRACT OF THE THESIS OF Seung-Ho Hong

Void fraction variations in a fractal-like branching channel network

Creator:: Cullion, Rebecca
Abstract:: Two-phase flow in a fractal-like branching microchannel heat sink may have enhanced heat transfer capabilities over single phase flow in the same branching channel network. In order to exploit this potential, a complete understanding of flow boiling in this geometry is required. The fractal-like geometry is similar to that of...
Resource Type:: Dissertation
Full Text:: -like network, fabricated for use in this study, utilized a circular configuration, in which fluid

Effects of orifice geometry and surface boundary condition on heat transfer of impinging jet array

Creator:: Kanokjaruvijit, Koonlaya.
Abstract:: The effects of the orifice geometry and the surface boundary condition on the heat transfer distribution to a flat surface of an impinging jet array were investigated. The jet array impinged normally onto the surface which was either isothermal or had a uniform heat flux. The experiments were performed for...
Resource Type:: Masters Thesis
Full Text:: presented for two jet geometries: circular and cusped ellipse. The cusped ellipse jets show better heat

Numerical design of a high-flux microchannel solar receiver

Creator:: Rymal, Charles
Abstract:: This thesis discusses the design of several microchannel solar receiver devices for use in CSP (concentrated solar power) using CFD (computational fluid dynamics) simulations. The goal is to demonstrate that, by taking advantage of the higher heat transfer coefficienct of microchannels, solar receivers can achieve higher efficiency than current receiver...
Resource Type:: Masters Thesis
Full Text:: . The high risk design features a circular micro-pin-fin array created using chemical etching and is

Flow characteristics of semi-confined impinging jet arrays

Creator:: Dano, Bertrand P. E.
Abstract:: The present study proposes to investigate the flow structure of different arrays of jets impinging on a flat surface enclosed by three walls, creating a channel that forces the air to leave in one preferential direction, generating a self sustain crossflow. Details of both the mean and some turbulence quantities...
Resource Type:: Masters Thesis
Full Text:: a circular orifice array while the second was a "cusped" ellipse array. The non-symmetry of the

Experimental investigation of supercritical heat transfer of carbon dioxide in parallel square microchannels with a single-wall constant heat flux boundary condition

Creator:: Zada, Kyle R.
Abstract:: In the vicinity of the pseudocritical point, supercritical carbon dioxide (sCO₂) undergoes a steep change in properties from “liquid-like” to “gas-like” as it is heated at a constant pressure. At the same time, there is a large spike in specific heat which can yield high heat transfer coefficients and heat...
Resource Type:: Masters Thesis
Full Text:: of supercritical CO2 has primarily focused on circular, uniformly heated channels at relatively low

Investigation into the role of strength and toughness in composite materials with an angled incident crack

Creator:: Grimm, Brian A.
Abstract:: Understanding the mechanical behavior of composite materials requires extensive knowledge of fracture behavior as a crack approaches an interface between the bulk material and the reinforcement structure. Overall material toughness can be greatly influenced by the propensity of an impinging crack to propagate directly through the substrate or deflect along...
Resource Type:: Masters Thesis
Full Text:: crack problem. A circular model based on the displacement field equations for mode-I fracture loading

ScholarsArchive@OSU

Fluid forces on and flow configurations around a circular cylinder near a plane boundary

Boundary layer control tests by suction on a circular cyclinder wing section

Laminar natural convection within long vertical uniformly heated parallel-plate channels and circular tubes

Monte Carlo simulation of radiation heat transfer in a three-dimensional enclosure containing a circular cylinder

Void fraction variations in a fractal-like branching channel network

Effects of orifice geometry and surface boundary condition on heat transfer of impinging jet array

Numerical design of a high-flux microchannel solar receiver

Flow characteristics of semi-confined impinging jet arrays

Experimental investigation of supercritical heat transfer of carbon dioxide in parallel square microchannels with a single-wall constant heat flux boundary condition

Investigation into the role of strength and toughness in composite materials with an angled incident crack

Limit your search

Academic Affiliation

Advisor

Commencement Year

Committee Member

Conference Name

Creator

Contributor

Date

Decade

Degree Field

Degree Level

Degree Name

File Format

Language

License

Non-Academic Affiliation

Peer Reviewed

Resource Type

Rights Statement

Subject

Search Constraints

Search Results

Limit your search