Search Constraints

Start Over
Filtering by: Committee Member Nairn, John Remove constraint Committee Member: Nairn, John Degree Name Master of Science (M.S.) Remove constraint Degree Name: Master of Science (M.S.) Resource Type Masters Thesis Remove constraint Resource Type: Masters Thesis

Search Results

  • Experimental characterization of saw chain cutting performance

    Creator:
    Otto, Andrew W.
    Abstract:
    Chainsaw users value cutting performance and safety. Knowledge of the forces exerted during sawing are necessary to understand and improve the cutting performance of saw chain. Additionally, cutting forces can be used to form metrics for evaluating performance tradeoffs when using a safety (i.e. low-kickback) saw chain versus a standard...
    Resource Type:
    Masters Thesis
    Full Text:
    : __________________________________________________________________ John P. Parmigiani Chainsaw users value cutting performance and safety. Knowledge of

  • Structural Design and Testing of Mass Timber Concrete Composite Floor Solutions with Acoustic Interlayers

    Creator:
    Srivastava, Mohit Raja
    Abstract:
    Timber-concrete composite (TCC) solutions originated in the early twentieth century. There has been a renewed interest in TCC solutions in modern mass timber buildings, especially for floor systems. However due to lack of data, design standards, and code acceptance, TCC solutions require that new mass timber solutions be tested, and...
    Resource Type:
    Masters Thesis
    Full Text:
    challenges and obstacles along the way. • To my committee members, Dr. Barbara G. Simpson, Dr. John Nairn

  • Numerical Modeling of Mass Timber Connections

    Creator:
    Hollenbeck, Sean R.
    Abstract:
    Cross-Laminated Timber (CLT) is a prefabricated building material that is relatively new to the United States and North America. It consists of no less than three layers of graded, dimensional lumber glued in alternating longitudinal and transverse layers to create a panel that can be used for various building applications...
    Resource Type:
    Masters Thesis
    Full Text:
    , Dr. Ari Sinha, Dr. Tom Miller and Dr. John Nairn, for providing valuable guidance and insight. Dr

  • A performance comparison of chainsaw bar lubricants

    Creator:
    Suryan, Levi J.
    Abstract:
    Chainsaws, an indispensable tool for modern forestry operations, rely on bar lubricant to prevent rapid wear of the chain and bar. Choice of bar lubricant must balance performance, cost, and biological impact. Many bar lubricants are available, but little published work exists that conclusively ranks the performance of these choices....
    Resource Type:
    Masters Thesis
    Full Text:
    committee members Dr. John Nairn and Dr. Rajiv Malhotra for providing high quality instruction, as well as

  • Pressure sensitive adhesives based on oleic acid

    Creator:
    Wu, Yili
    Abstract:
    Existing pressure sensitive adhesives (PSAs) are mostly based on petrochemicals. In this study, a novel PSA based on a renewable material, methyl oleate, was prepared and characterized. Methyl oleate was first epoxidized to form epoxidized methyl oleate that was subsequently hydrolyzed and acidified to form epoxidized oleic acid (EOA) which...
    Resource Type:
    Masters Thesis
    Full Text:
    . John Nairn, Dr. Chih-hung Chang, and Dr. Glenn Howe, for their time in reviewing my thesis and

  • Nanocomposites incorporating cellulose nanocrystals with potential applications in lithium ion batteries

    Creator:
    Kelley, Jeremiah (Jeremiah Joseph)
    Abstract:
    Cellulose nanocrystals (CNCs) have received considerable attention over the last ten years because CNCs can be produced from renewable materials such as straw, wood, cotton, and sea animals (tunicates). CNCs are slender rods with high aspect ratios (10-100) and the final dimensions of the CNCs depend on the starting material....
    Resource Type:
    Masters Thesis
    Full Text:
    John Simonsen Cellulose nanocrystals (CNCs) have received considerable attention over the last

  • Model development via delay extraction for the time-domain simulation of lossy transmission lines.

    Creator:
    Blevins, Chris
    Abstract:
    This thesis presents two new approaches for the broadband, time-domain modeling of lossy transmission lines. Each approach is based on an alternative derivation of delay extraction in order to separate the line's linear phase from its attenuation and dispersion. Augmentation networks represent the derived attenuation networks as rational function approximations....
    Resource Type:
    Masters Thesis

  • Side channel attack resistant elliptic curves cryptosystem on multi-cores for power efficiency

    Creator:
    Yoo, Jaewon
    Abstract:
    The Advent of multi-cores allows programs to be executed much faster than before. Cryptoalgorithms use long-bit words thus parallelizing these operations on multi-cores will achieve significant performance improvement. However, not all long-bit word operations in cryptosystems are suitable for parallel execution on multi-cores. In particular, long-bit words used in Elliptic...
    Resource Type:
    Masters Thesis
    Full Text:
    appreciation to Professor Huaiping Liu, Traylor Roger, and John A. Nairn for their serving in my graduate

  • Investigation into the role of strength and toughness in composite materials with an angled incident crack

    Creator:
    Grimm, Brian A.
    Abstract:
    Understanding the mechanical behavior of composite materials requires extensive knowledge of fracture behavior as a crack approaches an interface between the bulk material and the reinforcement structure. Overall material toughness can be greatly influenced by the propensity of an impinging crack to propagate directly through the substrate or deflect along...
    Resource Type:
    Masters Thesis
    Full Text:
    Toughness in Composite Materials with an Angled Incident Crack Abstract approved John P

  • Bending property enhancement of wood strand composite using viscoelastic thermal compression

    Creator:
    Rathi, Vardan M.
    Abstract:
    The fundamental intent of the study was to develop an innovative wood-strand composite for use in structural applications. Plantation grown, low density, hybrid poplar was used in the study which was found to be appropriate for the underlying Viscoelastic Thermal Compression (VTC) process. Wood modified by this process has high...
    Resource Type:
    Masters Thesis