Index Catalog // ScholarsArchive@OSU

Durability Assessment of Wood Composites Using Fracture Mechanics

Creator:: Mirzaei, Babak
Abstract:: The advent of synthetic adhesives has transformed the structural applications of wood. However, a persistent issue in adhesively-bonded wood products has been moisture durability. When designing wood based composites, moisture durability will depend on both the wood phase and the adhesive phase. A key question, therefore, is how does one...
Resource Type:: Dissertation
Full Text:: methodologies for durability assessment of wood composites and adhesives. Fracture resistance curves (R

Breaking radius of discolored wood in aircraft veneers

Creator:: Scheffer, Theodore C. (Theodore Comstock), 1904-2003, Duncan, Catherine G. (Catherine Gross), 1908-1968, United States. Division of Forest Pathology, and Forest Products Laboratory (U.S.)
Abstract:: The breaking radii of variously discolored veneers of six different hardwood species were small enough, for most of the discolorations, to indicate that such veneers can be used successfully on members having curved surfaces. When expressed in terms of the minimum radius of curvature attained without fracturing, the breaking radius...
Resource Type:: Technical Report
Full Text:: -511b, a ratio presumably could be substantìally less than 3.00 and the veneer still fracture on the

Veneer and plywood

Creator:: Van Wagner, Ralph
Resource Type:: Undergraduate Thesis
Full Text:: Veneer and plywood Qsi q VEIT.ER nnd PL?'TOOD RA

Development and design of veneer scarfing machinery

Creator:: Pearl, John Joseph
Resource Type:: Masters Thesis
Full Text:: Development and design of veneer scarfing machinery DÍ

Heat and mass transfer rates associated with the drying of Southern pine and Douglas fir veneer in air and in steam at various temperatures and angles of impingement

Creator:: Laity, Walter William
Abstract:: Southern pine and Douglas fir veneer samples were dried in air under the following conditions: air temperatures were 350, 600, and 750°F; air velocities were 50, 100, and 150 feet per second, and angles of impingement of air against the veneer surfaces were 0°, 45°, and 90°. The resulting drying...
Resource Type:: Masters Thesis
Full Text:: ) Title: Heat and Mass Transfer Rates Associated with the Drying of Southern Pine and Douglas Fir Veneer

Gluability of platen-dried Douglas-fir veneer

Creator:: Sandoe, Michael Dean
Abstract:: This study was undertaken to determine whether Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) veneer could be platen-dried and then sucessfully glued into two-ply parallel-laminated panels. A range of veneer thicknesses, platen temperatures and final dry moisture contents were examined. Thicknesses included were nominal 0.1, 0.2, 0.3 and 0.4 inches; platen temperatures...
Resource Type:: Masters Thesis

Effect of solvent extraction and planing of veneers from Southeast Asian species upon glueline characteristics and bond durability

Creator:: Dougal, Edward Francis
Abstract:: Using Southeast Asian hardwood veneers for exterior plywood siding has caused problems because some species produced quality plywood while other species produced plywood which delaminated soon after being put in service in exterior exposure. This study attempted to improve the durability of glue bonds of some Southeast Asian hardwood veneers...
Resource Type:: Masters Thesis
Full Text:: veneer surfaces and plywood gluelines of treated and untreated veneer. Stereo light microscopy, incident

Investigation of a new resin as an exterior adhesive to bond high moisture content veneers

Creator:: Clark, Randy Jon
Abstract:: A new carbohydrate-phenol based resorcinol resin (CPR resin) was synthesized by end capping a known carbohydrate-phenol based resole with resorcinol under basic reaction conditions. Synthetic parameters, such as duration of cook, pH, and the amount of resorcinol and formaldehyde were varied to produce resins with molecular weights (Mw) ranging from...
Resource Type:: Masters Thesis

Effect of peeling temperatures on Douglas fir veneer

Creator:: Corder, Stanley E., Atherton, George H., and Oregon State University. Forest Research Laboratory
Resource Type:: Technical Report
Full Text:: facilities and personnel a t73 SUMMARY To study the effect of heating logs on quality of veneer recovered

Outdoor exposure of container-grade paper-overlaid veneers

Creator:: Forest Products Laboratory (U.S.) and Mohaupt, Alvin A.
Abstract:: Information reviewed and reaffirmed 1965. Original report dated August 1959.
Resource Type:: Technical Report
Full Text:: variations between the panel materials used, some of which included several veneer and paper combinations

ScholarsArchive@OSU

Durability Assessment of Wood Composites Using Fracture Mechanics

Breaking radius of discolored wood in aircraft veneers

Veneer and plywood

Development and design of veneer scarfing machinery

Heat and mass transfer rates associated with the drying of Southern pine and Douglas fir veneer in air and in steam at various temperatures and angles of impingement

Gluability of platen-dried Douglas-fir veneer

Effect of solvent extraction and planing of veneers from Southeast Asian species upon glueline characteristics and bond durability

Investigation of a new resin as an exterior adhesive to bond high moisture content veneers

Effect of peeling temperatures on Douglas fir veneer

Outdoor exposure of container-grade paper-overlaid veneers

Limit your search

Academic Affiliation

Advisor

Commencement Year

Committee Member

Conference Name

Creator

Date

Decade

Degree Field

Degree Level

Degree Name

File Format

Language

License

Non-Academic Affiliation

Peer Reviewed

Resource Type

Rights Statement

Subject

Search Constraints

Search Results

Limit your search