A unique microreactor-assisted nanomaterial synthesis and printing process was studied for the fabrication of patterned metal oxide nanostructured thin films. The process uses a continuous flow microreactor to control and generate a reactive chemical flux that was transported to a patterned microfluidic channel. The microreactor-assisted nanomaterial synthesis process can generate...
The purpose of this research is to provide a simple fabrication method for zinc oxide and antimony sulfide based thin film solar cells. Both a ZnO nanorod electron conducting structure and a stibnite absorber show promise in a solar cell. Initial attempts at using only ZnO and Sb2S3, however, resulted...
Bubble nucleation control, growth and departure dynamics is important in understanding boiling phenomena and enhancing nucleate boiling heat transfer performance. We report a novel bi-functional heterogeneous surface structure that is capable of tuning bubble nucleation, growth and departure dynamics. For the fabrication of the surface, hydrophobic polymer dot arrays are...
Copper zinc tin sulfide (CZTS) is a potential solar material for thin film solar cells according to its suitable band gap in the visible light range, high absorption coefficient, low toxicity, good photostability and relative earth abundance of component elements. However, the production cost of this solar thin film material...
Covalent organic frameworks (COFs) are an emerging type of microporous crystalline polymers connected by organic units via strong covalent bonds. Due to the well-defined crystalline structure and excellent chemical and thermal stabilities, COF materials are being considered as promising candidates in a variety of applications, such as gas adsorption, catalysis...
Photoluminescence (PL) materials have attracted a lot of attention in last several decades. Recently PL materials, which can convert low-efficiency Ultraviolet (UV) or Infrared (IR) light to high-efficiency visible light, have been widely applied in the research of improving conversion efficiency of solar cell. As one of the most common...
Inkjet-printed p-type copper(I) iodide-based TFTs were successfully fabricated. As-printed copper(I) halide semiconductor films, such as CuI, CuBrI, and CuClI, were used as p-type active channel layers for TFTs. The entire process of the TFTs fabrication was maintained under 150 °C, which is compatible with flexible plastic substrates and transparent glass...
Digital printing techniques offer several advantages in manufacturing electronics such as direct writing of materials, reduction of chemical waste, and scalability. In particular, printing can significantly simplify manufacturing processes by directly defining the channel area, the gate, and the source and drain contacts, allowing for lower costs and higher throughput...
Transparent and electrically conductive metal oxide nanoparticles have attracted much attention, and can be used to improve the performance of solar cells, transparent electrode materials, and gas sensor technology. Specifically, indium tin oxide (ITO) nanocrystals (NCs) are potentially useful nanomaterials, having technological applications in enhanced sensitivity of optical spectroscopy due...
Light trapping plays a phenomenal role in enhancing light confinement and light absorption within the solar cells, thus increasing the optical efficiency of the cell. Different strategies are employed for trapping light photons within the cell. Methods used include a substrate or single layer texturing, light trapping coating, plasmonic gratings,...
Digital inkjet printing is developing quickly today because inkjet printing processes consume less energy and water and produce less waste discharge than traditional dyeing and other printing technologies. Inkjet printing provides more versatility and flexibility in terms of printing patterns and colors. Natural pigments are gaining more attention today as...
Mg-MOF-74 is one type of metal-organic frameworks (MOFs) that is widely known for its excellent CO2 uptake capacity. More intriguingly, it can be used to detect low levels of toxic gas such as CO2. Currently, most research into Mg-MOF-74 focuses on using the powder type as a CO2 absorbent because...
In Intense Pulsed Light (IPL) sintering, pulsed large-area visible light from a xenon lamp is absorbed by nanoparticle films or patterns and converted to heat, resulting in rapid sintering of the nanoparticles. This work experimentally characterizes IPL sintering of silver nanoparticle films. A newly observed turning point in the evolution...
The continuous development of higher performing battery materials has emerged in parallel with the development of new manufacturing processes. Nanomaterials are one solution to addressing the cycling and performance challenges that limit existing battery cells. However, many of the methods used today for nanomaterial synthesis are high temperature batch methods...
Boiling heat transfer is studied for its ability to dissipate high fluxes and achieve heat transfer coefficients two orders of magnitude greater than single-phase heat transfer systems. Heater surface enhancement with increased surface area, varied geometry, wettability contrast and micro/nano-structures can further enhance boiling heat transfer performance through bubble nucleation...
There is an emerging interest in developing wearable electronics as a platform, which
provides the flexibility of a wearable while maintaining its promising functionality as smart textiles. Metal-halide semiconductors are attractive materials with tunable optical and electrical properties. Researchers have widely studied and applied it for advanced
photonics and optoelectronic...
As a group of promising semiconductor materials, metal chalcogenides in thin film form have been widely used in electronics and optoelectronics applications, such as solar cell devices and photon sensors. Unfortunately, the film size and product throughput are limited by the current vacuum-based thin film deposition techniques. Solution-based thin film...
Zinc Sulfide (ZnS) thin film, with a wide band gap, has been used for many applications, such as buffer layer for CIGS solar cells, light emitting diodes and thin film electroluminescent devices.
In this work, ZnS thin films were prepared using two different deposition processes. In the first method, ZnS...
Worldwide production of natural gas has surged in the last few decades leading to an economic windfall for many communities, but sometimes these new sources of natural gas are located in geographically isolated locations. These areas are so remote that it isn’t economically feasible to transport this stranded gas to...
To become a competitor for fossil fuels such as coal, solar installations will need to be produced and installed at a price equal to or below grid parity. This price can be approached by either reducing the overall system cost or increasing system efficiency. The focus of this paper is...