To facilitate the design of Natural and Nature-Based Features (NNBF) for flood protection, this thesis expands an existing engineering design methodology to NNBF systems. The existing approach is a Level III reliability method for the performance-based design of traditional coastal engineering systems. The expanded methodology incorporates uncertainties inherent to both...
Reinforced concrete (RC) column-footing substructures are widely used to support bridges along critical transportation corridors in Oregon. Those built prior to 1971 were typically designed to resist only gravity loads. Therefore, they are vulnerable to damage or collapse during strong ground shaking. To prevent collapse, seismic retrofits have been developed...
This study investigates the microstructure and mechanical properties of an austenitic Oxide Dispersion Strengthened (ODS) steel produced by the Laser Directed Energy Deposition (LDED) process using powder feedstock atomized with elemental yttrium. The Microstructure of the samples was characterized by electron microscopy, and mechanical properties were measured using a tensile...
Thermal wave imaging (TWI), a technology based on heat conduction and radiation through materials, is a relatively new addition to current non-destructive inspections (NDI) systems. Bonding of composites, an extremely important step in manufacturing and repair of laminates, could be affected by defects originating from faulty manufacturing processes or damages...
The characterization of the seismic performance of structures relies on numerical simulations. However, estimates of seismic response are subject to various sources of uncertainty, including modeling uncertainty. This research estimated the response of two full-scale structural specimens composed of a moment resisting frame, elastic spines, and force-limiting connections (FLC), which...
Post-tensioned (PT) self-centering shear walls were designed to reduce structural damage from seismic activity. However, these lateral force resistant systems experience post-tension loss negatively affecting the re-centering capability due to delayed deformations experienced by engineered wood products over time. The long-term mechanical response of mass-timber panels to in-plane PT loads...
This thesis presents two conceptually linked papers outlining methodologies to improve community resilience. Both papers employ Seaside, Oregon as a testbed community and consider the seismic-tsunami hazard posed by the Cascadia Subduction Zone. The first paper presents a framework to deaggregate the results of a multi-hazard, multi-infrastructure, damage analysis by...
Reliability-based geotechnical foundation design focusses on soil and structure analysis that meets necessary safety, performance and/or serviceability criteria, calibrated based on probabilistic analyses and an accepted level of risk. As the civil engineering community seeks to better harmonize geotechnical and structural design methodologies, reliability-based design is being incorporated more into...
Situated cognition theory emphasizes the role that social and material contexts have on learning and knowledge application. Several studies of engineering workplace environments have noted differences between the social and material contexts of the workplace and those of undergraduate engineering education. No existing research has studied the social and material...
Timber engineering is currently in the midst of a significant evolution due to the rise of mass timber products, like cross-laminated timber (CLT). Increasing numbers of structural engineers are facing the challenge of designing lateral-force-resisting systems (LFRS) for multistory CLT structures. LFRS solutions such as steel frames, concrete cores, or...
In the last few decades new trends and innovations in wood products have emerged that are changing the way we can use this material in buildings. Additionally, wood is a material that has been touted to have many positive attributes in comparison to nonrenewable construction materials such as steel and...
Drilled shaft foundations provide significant geotechnical resistance for support of structures, such as highway bridges, traffic sign, and signal pole structures, and are used widely to meet their structural foundation requirements. The amount of steel reinforcement in drilled shaft foundations has increased over the past several decades to account for...
The first goal of this master’s thesis was to investigate the linkage between a non-destructive testing method, surface resistivity, and premature concrete deterioration brought on by chloride ingress and or freeze-thaw cycling. The experimental method for this project consists of taking surface resistivity measurements of reinforced concrete slabs after they...
Manufacturing exists as a stronghold for continuous growth and development of economies, a trend that is likely to continue as the demand for commodities and products grow. Manufacturing drives innovation and productivity in developed nations, as well as promoting economic stability and development in developing nations. However, manufacturing activities pose...
Significant amounts of uncertainty owing to both modeling decisions and inherent randomness are present in simulating the material and geometric nonlinear response of structural systems to extreme loading. Computing the sensitivity of structural response with respect to model parameters indicates which parameters have the largest affect on the response, which...
Cross-laminated timber (CLT) is a massive engineered wood product made of orthogonally bonded layers of solid-sawn lumber, and is intended for roof, floor, or wall applications. Although it was developed in Europe in the early 90s, CLT is relatively new to North America.
CLT products must be certified for structural...
The goal of this project is to contribute to the development of design values for cross-laminated timber (CLT) diaphragms in the seismic load-resisting system for buildings. Monotonic and cyclic tests to determine strength and stiffness characteristics of 2.44 m (8 ft) long shear connections with common self-tapping screws were performed....
Composites often are able to carry more load after damage due to the structure of laminates. In addition, damage can be difficult to detect in composites compared to homogeneous materials. Understanding the behavior of composite material after damage is vital for composite structural design. Currently, experimental methods exist for classifying...
Aging and deficient infrastructure has become a major problem throughout the world. This is particularly evident in the case of reinforced concrete (RC) bridges. The cost of replacing these bridges is often prohibitive, thus engineers must find ways to strengthen them. Many older RC bridges predate the modern understanding of...
Sustainable product design is becoming an important component of the development of consumer products. Currently there are limited design resources to aid in the creation of environmentally sustainable products. The purpose of this research is to theorize a new method for integrating sustainable design knowledge into the early design phase...