This thesis presents a comparison of time-domain and frequency-domain algorithms for phase noise calculation in oscillators. Floquet theory provides the mathematical foundation for these calculations and the numerical methods employ perturbation projection vectors (PPVs). The PPVs are an estimate of an oscillator's sensitivity to noise.
The in-house circuit simulator SPICE3...
As the Tekbots program expands into senior and graduate level classes at Oregon State University, so does the need arise for more complex learning platforms. These complex hardware platforms cannot be adequately tested in a manufacturing environment as we have done previously. Also, due to their complexity, these platforms require...
With the growing demand for portable/consumer electronics, such as digital
audio/video (AV), the downscaling of device dimensions, which enables the
integration of an increasing number of transistors in a single chip, is mandatory.
This trend also continuously pushes the power supply voltage down to reduce the
power consumption and improve...
The importance of wind-driven latent heat fluxes for supporting tropical intraseasonal precipitation variability is analyzed. Tropical
intraseasonal variability in the west pacific and Indian ocean is analyzed for northern and southern hemisphere summer during 1999-2005 using
satellite and buoy observations. A composite analysis of QuikSCAT ocean vector winds and TRMM...
Multiple-input multiple-output (MIMO) communication systems have recently been considered as one of the most significant technology breakthroughs for modern wireless communications, due to the higher spectral efficiency and improved link reliability. The sphere decoding algorithm (SDA) has been widely used for maximum likelihood (ML) detection in MIMO systems. It is...
Low noise oscillators are universally needed in digital systems for clock generation and synchronization, and in radio-frequency communication front-ends for frequency up- and down-conversion. Noise in oscillators results in timing jitter, and limits the clock frequency of digital systems. In radio-frequency communication systems, phase noise in oscillators lowers the signal-to-noise...
A new group of lead free piezoelectric perovskite solid solutions, (1-x)Bi(B'B")O₃-xABO₃, were obtained via solid-state processing techniques. The solubility of unstable perovskite Bi(B'B")O₃ compounds into stable perovskite compounds was found to be related to the tolerance factor of the ABO₃ perovskite endmembers. The morphotropic phase boundary (MBP) in perovskite solid...
The primary objective of this thesis is to develop a process for fabricating integrated circuits based on thin-film transistors (TFTs) using zinc tin oxide (ZTO) as the channel layer. ZTO, in contrast to indium- or gallium-based amorphous oxide semiconductors (AOS), is perceived to be a more commercially viable AOS choice...
Dynamic CMOS circuits are commonly used in high-performance memory arrays to implement wide-NOR logic functions for their read and search operations. This is because dynamic circuits have significantly higher speed and lower area compared to static circuits for performing similar operations. Register File (RF) arrays are located at the top...
Periodic metal and metal-dielectric composite nanostructures have been of interest from the field of plasmonics and metamaterial fabrication. In order to exploit the behavior of these unique materials in the visible region of the optical spectrum, these structures need to be significantly shorter than the wavelength of response, and hence...
The effect of ambient environment on the fatigue behavior of two Zr-Ti-Cu-Ni-Be bulk metallic glasses (BMGs) is examined in the present study. The first metallic glass, Zr₄₄Ti₁₁Ni₁₀Cu₁₀Be₂₅, was tested to establish the presence of an environmental effect in the fatigue growth curve measured in ambient air. Fatigue growth curves produced...
Azaspiracid has generated an enormous amount of scientific interest in the fourteen years since its initial discovery. The structure contains a 6,5,6 bis-spiroketal, a [3.3.1] bicyclic ketal and a 6,5-spiroaminal linkage as key moieties. With 9 rings, 20 stereocenters and three alkenes, the azaspiracid immediately attracted the interest of the...
Currently, the temporal arc distribution across the ingot during the vacuum arc remelting (VAR) process is not a known or monitored parameter. It is has previously been shown that arcs can spatially constrict during VAR, and this constriction can lead to undesired defects in the material. Additionally, correct accounting for...
Customer requirements and engineering specifications will influence the direction of the design in any product, so it is crucial to make the requirements as stable as possible so quality designs can be produced on time within a budget. It would be optimal for requirements and specifications to remain constant but...
The development of microfluidic devices for heavy metal extraction is presented in this dissertation. Various research areas, covering subjects from photochromic compound syntheses to microchip fabrication techniques are explored to develop microfluidic devices capable of extracting heavy metal ions from drinking water. Through integration of the beneficial characteristics of both...
The next generation of high temperature structural alloys must exhibit exceptional resistance to fracture, creep, oxidation, and fatigue at high temperatures. Chromium is being considered due to its high melting point (>1800°C), relatively low density (~7.2 g/cc), high temperature strength, and oxidation resistance. Limiting the use of chromium is its...
Photovoltaic (PV) cells have long been an attractive alternative for the consumption of fossil fuels but current manufacturing practices suffer from poor energy efficiency, large carbon footprints, low material utilization, high processing temperatures and high solvent usage. A critical step in PV production is the deposition of CdS as a...
Oil drilling requires that miles of steel drill pipe, called the drill string, be exposed to fatigue loading and corrosive environments. Furthermore, it has been reported that pitting corrosion is responsible for initiating catastrophic drillstring failure. Pitting corrosion is responsible for initiating fatigue cracks, with pits acting as local stress...
The purpose of this study is to synthesize and characterize the nanoporous structures that can be obtained by the anodization of thin film aluminum sputter deposited on a silicon wafer substrate. This study also investigated the application of nanoporous alumina to fabricate nanorod arrays by using preceramic polymers. Although there...