Index Catalog // ScholarsArchive@OSU

Products liability in the electronics industry

Creator:: Smith, Milton Ray
Abstract:: This thesis discusses the field of products liability as it relates to the electronics industry. The historical development of products liability is traced and the various legal theories are examined. These legal theories and background are then used to discuss the judicial obligations imposed upon the manufacturer and seller of...
Resource Type:: Masters Thesis
Full Text:: for the uses intended, meaning that if there is a reasonably easy means available at the time that

Stiffness matrix analysis of structures by electronic digital computer

Creator:: Serpanos, James Evan
Resource Type:: Masters Thesis
Full Text:: iteration techniques of solution of simultaneous equations is becoming less desirable. The electronic

The binistor as an electronic switching element

Creator:: Ballieu, Howard Lee
Resource Type:: Masters Thesis
Full Text:: University on thesis matters is greatly appreciated.. Two representatives of Transitron Electronic

A mathematical method of evaluating the reliability of electronic equipment

Creator:: Lindquist, Claude S.
Abstract:: Reliability, the probability that a system will not fail but will perform correctly at least until some arbitrary time, is becoming an increasingly important concept in electronic system design. This probability is evaluated using probability density functions which are obtained analytically by forming mathematical expressions describing the failure distributions of...
Resource Type:: Masters Thesis
Full Text:: correctly at least until some arbitrary time, is becoming an increasingly important concept in electronic

A low time constant electronic integrator for time dependent functions

Creator:: Mueller, Robert Allen
Resource Type:: Masters Thesis
Full Text:: - ond unit Is a low time constant electronic integrator for time depen- dent functions for determining

Photomechanics of stress transfer mechanisms in composite materials

Creator:: Edelman, Walter E.
Abstract:: A study of stress transfer near the ends of the whisker in a simulated whisker reinforced composite material was conducted by using photoelastic techniques. The composite material studied was αAl₂O₃ whiskers in an aluminum matrix. The photoelastic models used consisted of a scaled-up macroscopic stiffener embedded in a three-dimensional epoxy...
Resource Type:: Dissertation
Full Text:: material the carbon is not readily observable in the finished material. In another class of combined

The design of a mechanism for tensile testing in a liquid helium Dewar

Creator:: Fullman, Carl Harvey
Resource Type:: Masters Thesis
Full Text:: privacy Ian of C-rauate School Date thesis is oreserìted kq/%j // Typed by Eloise Allison

A circuit design to generate and maintain a constant magnetic flux

Creator:: Tuntawiroon, Chalermchai
Abstract:: A circuit designed to generate and maintain a constant magnetic flux is presented by using a sample-data control system, instead of a continuous control system. A Hall generator is used as the magnetic sensing element, and is operated with a pulse bias to allow a large output. The output of...
Resource Type:: Masters Thesis
Full Text:: . INTRODUCTION The purpose of this thesis is to report on the design of a simple electronic circuit that will

An integrated analog multiplier circuit

Creator:: Traa, Einar
Abstract:: The exponential characteristic of the base-emitter Junction in bipolar transistors was used to make an accurate and fairly temperature independent multiplier. Using hybrid-pi transistor models and ECAP, a bandwidth of 350 MHz was predicted. Linearity is limited by emitter degeneration in the input differential stage rather than by the small...
Resource Type:: Masters Thesis
Full Text:: samples are available it can be measured. It is approximately equal to the Zener impedance of the

Critical buckling load for round tapered columns with variable end fixity

Creator:: Dotson, George Franklin
Abstract:: The critical buckling load for round tapered columns with variable end fixity is presented. The theory used is presented together with the general solution for the resulting differential equation. This general solution is solved by use of a computer. The computer program written specifically for this thesis, the flow chart,...
Resource Type:: Masters Thesis
Full Text:: to columns of any material, it is especially important to the timber industry since the data is

ScholarsArchive@OSU

Products liability in the electronics industry

Stiffness matrix analysis of structures by electronic digital computer

The binistor as an electronic switching element

A mathematical method of evaluating the reliability of electronic equipment

A low time constant electronic integrator for time dependent functions

Photomechanics of stress transfer mechanisms in composite materials

The design of a mechanism for tensile testing in a liquid helium Dewar

A circuit design to generate and maintain a constant magnetic flux

An integrated analog multiplier circuit

Critical buckling load for round tapered columns with variable end fixity

Limit your search

Academic Affiliation

Advisor

Commencement Year

Committee Member

Conference Name

Creator

Contributor

Date

Decade

Degree Field

Degree Level

Degree Name

File Format

Language

Location

Non-Academic Affiliation

Peer Reviewed

Resource Type

Rights Statement

Subject

Search Constraints

Search Results

Limit your search