A circuit designed to generate and maintain a constant magnetic
flux is presented by using a sample-data control system, instead of a
continuous control system.
A Hall generator is used as the magnetic sensing element, and
is operated with a pulse bias to allow a large output. The output of...
It is often necessary in communication systems to detect very
small signals that are buried in noise. One device used to accomplish
this is a lock-in amplifier. Initially the theory of operation is considered.
Then the circuit design of a low cost lock-in amplifier is
given. The amplifier, employing linear...
The use of the exponential-transfer-characteristics of a transistor
junction as a means of giving a logarithmic sweep calibration to a
sampling oscilloscope is presented. The prior work in logarithmic
converters leading up to the use of the transistor's transfer properties
is explored. A circuit adapting a sampling oscilloscope to a...
In this thesis a method is presented for maintaining the left
ventricular wall stress of the human heart at a constant level during
the systole (active portion of the heart's cycle). This constant stress
level makes it possible to take isotonic measurements on the heart
muscles.
The left ventricle of...
This paper is concerned with the design of a 21-bit
metal-oxide-semiconductor field-effect transistor (MOSFET)
integrated circuit static shift register.
This circuit consists of three separate 1, 4, and
16-bit static shift registers constructed on a single
monolithic chip, each with independent input and output
terminals.
Type D flip-flops are used...
In recent years the types of engineering data accumulated by many telemetry systems have become so diversified and complex, and
the environment in which these systems operate has become so restricting
that telemetry systems with increased capabilities and decreased
size are becoming a necessity. Advances in integrated circuitry
techniques satisfy...
An analog simulation of the postural control system (PCS) of a
dog is used to illustrate how modern systems simulation can be applied
to a study of complex life systems. Even though many bold
assumptions were required to adequately simplify the PCS model, the
simulation provided intuitive insight and gave...
The three-phase squirrel-cage induction motor is rugged, compact,
inexpensive, can be totally enclosed and requires little maintenance.
Its use as a variable speed drive has been limited, however, by the
state-of-the art of control components.
The advent and continuing development of the silicon controlled
rectifier and associated solid-state components has...
The stability of a third-order, nonlinear system with a
saturation characteristic was studied by applying the second method
of Liapunov, which is the most general approach currently used for
dynamic systems.
This thesis presents (1) the analysis of a third-order, nonlinear
system, (2) a suitable Liapunov function, generated by the...
In this thesis, characteristics of coupled trigonometric transmission
lines are studied, based on the general theory of nonuniform
transmission lines. The four-port transmission matrix parameters
of the coupled trigonometric transmission lines are derived from the
even and odd mode waves. Two applications of coupled trigonometric
transmission lines are presented; one,...
The paper is a study of (i) the realization of the gyrator,
(ii) active filter synthesis using gyrator.
Several realization methods of the gyrator are summarized.
A practical gyrator composed of two operational amplifiers was built
and tested. The experimental results are shown. Two RC-gyrator
synthesis techniques are derived and...
This paper is a study of the design of an integrated MOS addressing
circuit by using the modified two-phase dynamic shift register. This modified circuit is compared to the conventional two-phase
dynamic SR and discussed briefly. The resulting circuit shows
several advantages to improve the essential conditions of integrated
circuit...
The problem of analyzing the general linear, time-varying
system is investigated. The approach starts with four different
system representations: the differential equation, transform representations,
signal flow graphs, or block diagrams. Given one of
these system describing representations, it is shown what the
engineer can find out about the system and...
In this paper the characteristics of multi-conductor transmission
lines have been investigated for a variety of termination conditions
by using the differential equations and matrix methods.
Equations showing the characteristics of traveling waves along loss-less
multi-conductor systems are derived.
Line parameters were evaluated by experiments and by calculations.
The results...
A method is presented for developing a detailed non-linear
voltage regulator system model representation for use in power
system stability studies. This model is implemented within MIMIC,
a digital simulator program, with a particular set of data which
could be taken from field tests. Results are presented from simulations
of...
A high speed adaptive signal processing concept and several high
speed adaptive logic circuit elements are presented.
The adaptive signal processing system operates in a "goal" oriented
mode; the system tries to optimize its characteristics to
achieve a given goal in spite of unforeseen variations in the inputs,
the system,...
A consumer orientated simulation of rotary solenoid performance
allows the user to determine what effects non-standard conditions
will have on performance in a contemplated application. Typical
variable conditions are: loads temperature and voltage.
Three differential equations are used to describe the solenoid
operation. Two of these are non-linear, second-order equations...
This thesis discusses the field of products liability as it
relates to the electronics industry. The historical development of
products liability is traced and the various legal theories are
examined. These legal theories and background are then used to discuss
the judicial obligations imposed upon the manufacturer and
seller of...
In this thesis, we are concerned with the synthesis of a
specified voltage ratio transfer function having a specified complex
termination. A method for the active network synthesis with specified
complex termination using resistive and capacitive elements and only
one negative impedance converter is presented. The synthesis
technique involves rearranging...