In recent years, there has been growing interest in both industry and academia to use continuous-time (CT) Δ-Σ A/D converters for wideband wireless and wireline communication applications.
So far no reported CT Δ-Σ A/D modulator achieves 14-bit or higher dynamic range (DR) with more than 2MHz signal bandwidth (equivalently 4MS/s)....
Traditionally linear actuator applications are addressed by the use of hydraulic systems. The high maintenance cost and poor reliability will always be the most critical problem in the real applications. Benefited from both the high mechanical advantage of the roll screw and the simple structure of the switched reluctance motor,...
This thesis presents a comparison of time-domain and frequency-domain algorithms for phase noise calculation in oscillators. Floquet theory provides the mathematical foundation for these calculations and the numerical methods employ perturbation projection vectors (PPVs). The PPVs are an estimate of an oscillator's sensitivity to noise.
The in-house circuit simulator SPICE3...
Designing spectral efficient, high-speed wireless links that offer high quality-
of-service and range capability has been a critical research and engineering challenge. In this thesis, we mainly address the complexity and performance issues of
channel estimation and data detection in multiple-input multiple-output (MIMO)
orthogonal frequency division multiplexing (OFDM) systems over...
Continuously tunable diode laser sources coupled to single-mode fiber are useful sources for fiber Bragg grating (FBG) strain sensors. This paper describes the
development and fabrication of such a device. An introduction is given describing
applications of tunable lasers and some of the different methods of creating a tunable
diode...
The purpose of this thesis is to explore dependency speculation in Dynamic Simultaneous Multi-Threading (DSMT). DSMT is a microprocessor architecture which attempts to extract Thread Level Parallelism (TLP) from single-threaded programs at run-time. This is accomplished by running multiple iterations of program loops in parallel. The DSMT architecture was originally...
There is a large and growing market for portable consumer audio products
with very small size. As the size of these products is reduced, the area occupied
by batteries becomes significant and hence limits the number of batteries to one.
In order to build such small products, high levels of...
Commonly proposed ocean wave energy converters (OWEC) use inefficient and maintenance demanding intermediate hydraulic and pneumatic systems. We propose a novel rotary direct-drive OWEC that eliminates these intermediate stages. The new device employs a contactless force transmission system (CFTS) comprising a “piston” and a “cylinder” and a ball screw to...
This thesis presents a Z-parameter based model to predict the substratenoise coupling between two contacts in a heavily doped substrate for frequenciesless than 2 GHz. The empirical model is scalable with contact size and spacingsbetween the contacts and model parameters can be readily extracted from simu-lated or measured data. The...
Recently, continuous-time ΔΣ modulators are appearing increasingly often in both the literature and the marketplace due to their features of inherent antialiasing and relaxed requirements for opamp and so on. However, several nonideal factors such as clock jitter, excess loop delay, inter-symbol interference and so on, degrade the SNR performance...
Digital-to-analog converters (DACs) suffer from static and dynamic nonlinearity problems, which degrade their accuracy and performance. Mismatch errors in the analog components restrict the maximum achievable linearity.
This thesis presents various techniques for correcting these errors. It describes a correction process for the nonlinear behavior of DACs, on three different...
A discrete trap model is developed and employed for elucidation of thin-film transistor (TFT) device physics trends. An attractive feature of this model is that only two model parameters are required, the trap energy depth, E[subscript T], and the trap density, N[subscript T]. The most relevant trends occur when E[subscript...
With the ever-increasing demand for portable devices used in applications
such as wireless communication, mobile computing, consumer electronics, etc.,
the scaling of the CMOS process to deep submicron dimensions becomes more
important to achieve low-cost, low-power and high-performance digital systems.
However, this downscaling also requires similar shrinking of the supply...
Ferrites have been used for various high frequency applications as bulk
materials. These applications, however, are limited to large dimension devices. In
this thesis, thin film ferrites were deposited from a low temperature solution-based
deposition process that is suitable for micro-scale high frequency applications. The
low temperature nature of this...
Ultra-wideband (UWB) radio is the transmission of data using an extremely wide bandwidth and very low power spectral density. In this thesis, the mereits and challenges of UWB architectures versus conventional narrowband architectures will be compared. Pulsed UWB systems can be implemented with very simple architectures. These advantages make UWB...
A large number of sequential decision-making problems in uncertain environments
can be modeled as Markov Decision Processes (MDPs). In such settings, an agent
can observe at each time step the state of the environment and then executes an
action, causing a stochastic transition to a new state of the environment...
Previous research has revealed gender differences that impact females’ willingness to adopt software features in end users’ programming environments. Since these features have separately been shown to help end users problem solve, it is important to female end users’ productivity that we find ways to make these features more acceptable...
End-user programmers, because they are human, make mistakes. However, past research has not considered how visual end-user debugging devices could be designed to ameliorate the effects of mistakes. This paper empirically examines oracle mistakes mistakes users make about which values are right and which are wrong to reveal differences in...
Digital phase-locked loops (PLLs) have been receiving increasing attention recently due to their ease of integration, scalability and performance comparable to their analog counterparts. In digital PLLs, increased resolution in time-to-digital conversion is desirable for improved noise performance. This work describes the design and simulation of a stochastic time-to-digital converter...
The design of a 10-bit pipelined charge redistribution DAC employing MOSCAPs biased in their accumulation mode is presented in this thesis. A switched capacitor filter and output buffer have also been designed for the system. The effect of MOSCAP nonlinearity on the performance of the pipelined charge redistribution DAC has...
Circuits operating outside the earth’s atmosphere are more vulnerable to cosmic radiation and require special design consideration. The purpose of this work is to explore methods of mitigating the effect of radiation in phase locked loop (PLL) circuits. Several voltage controlled oscillators (VCOs) and two complete PLLs are designed and...
Spacecrafts experience radiation in the course of their operation
and all electronic equipment on board these spacecrafts has to
be designed to withstand the effects of this radiation.
This thesis describes the effects of total ionization dose (TID)
and single event transients (SET) in phase-locked loops - an
important circuit...
The detection of motor faults at their incipient stage is of prime importance to any industrial plant. The introduction of adjustable speed drives has improved the control and the efficiency of induction motors, however, this has changed the nature of motor faults and how they can be detected.
Current signature...
At frequencies exceeding 1-2 GHz, the substrate network models used in substrate coupling simulation must account for the reactive nature of the substrate. Unlike at low frequencies, where the purely resistive substrate models can be validated through DC resistance measurements, these high-frequency models, comprising reactive components, must be validated through...