This paper describes the analysis of data from a three-year gross time study of skyline, balloon, and helicopter yarding systems operating in Western Oregon. Data collection activities were designed and supervised by the Pacific Northwest Forest and Range Experiment Station, U.S.D.A. Forest Service. The specific logging systems studied were running...
This paper describes the analysis of data from a three-year gross time study of skyline, balloon, and helicopter yarding systems operating in Western Oregon. Data collection activities were designed and supervised by the Pacific Northwest Forest and Range Experiment Station, U.S.D.A. Forest Service. The specific logging systems studied were running...
Unrelated parallel machines are machines that perform the same function but have
different capacity or capability. Thus, the processing time of each job would be different
on machines of different types. The scheduling environment considered is dynamic in
both job release time and machine availability. Additionally, each job considered can...
A comparison of two procedures which allocate inspection effort
within a production sequence is presented here. The concern
for quality and the need to hold down the costs of quality has resulted
in mathematical models which locate inspection so that the
desired quality is attained at a minimum cost.
In...
This dissertation addresses the "multi-machine carryover sequence
dependent group-scheduling problem with anticipatory setups," which arises in
the printed circuit board (PCB) manufacturing. Typically, in PCB manufacturing
different board types requiring similar components are grouped together to
reduce setup times and increase throughput. The challenge is to determine the
sequence of...
Small, independent logging contractors can benefit
from cost control and cost planning. This report
details the labor and equipment cost components of a
logging crew. Records, both required and available for
determining costs, are discussed. Recommended costing
procedures are illustrated. Although the study took
place in the Pacific Northwest, the...
This thesis is intended to provide the management of small to medium sized job shop companies with a written plan to implement a formal computerized manufacturing planning and control system. The research stemmed from a case study performed at a typical job shop where growth of production activities was complicating...
This dissertation addresses a hybrid-flow shop scheduling problem with dual resource constraints in a supply chain. Most of the traditional scheduling problems deal with machine as the only resource. However, other resources such as labor is not only required for processing jobs but are often constrained. Considering the second resource...
The objective of this research project was to identify the limitations associated
with schedule-based Material Requirements Planning (SBMRP) and to
present a knowledge-based expert system (KBES) approach to solve these problems.
In SBMRP, the basic strategy is to use backward or forward scheduling
based on an arbitrary dispatching rule, such...
In northeast China, logging has three stages; timber
harvest, transportation and the operations inside a timber
yard. The timber yard is an intermediate transhipment point between truck transport and rail transport to manufacturing centers. The transhipment capacity of the timber yard is often the limiting acitivity in the logging chain....
A multistage production system consists of a number of
production stages that are interrelated, that is the output
from one stage forms input to the next stage. There are
constraints associated with each stage as well as constraints
imposed by the overall system. Besides, there are multiple
objectives that need...
This research was motivated by the use of multi-track feeders in the printed
circuit board (PCB) assembly. In a low volume, high mix production environment,
setup time is usually considered more important than processing time. Implementation
of multi-track feeders not only increases the capacity of the surface mount
machines but...
Manufacturing industry drives economic activity and growth around the world, but manufacturing activities consume large amounts of material, energy, and labor resources. Therefore, the impacts of manufacturing need to be accounted for and reduced. Direct benefits of manufacturing are products and income, which, in turn, influence the lives of people...
Productivity Interfirm Comparison (PIC) is a simple
method used to improve productivity at the firm level,
where a number of firms operate in the same product line so
that performance information on the firms can be compiled
and compared. This results in identifying potential areas
for improvement or exploitation. The...
The principal objective of this study was to investigate process simulation and
optimization of an existing offshore natural gas process which needed profitability
improvements. Optimization was done using two alternative approaches: a global
approach (response surface methodology) or a local approach (successive quadratic
programming). The global approach was characterized by...
Determining the performance characteristics of various ocean wave energy converters (OWEC) has proven to be difficult due to problems replicating a baseline motion profile in the ocean or wave tank to compare these devices. The linear test bed seeks to mechanically simulate the relative linear motion between the active components...
Feedlot finishing of beef cattle in Southern Alberta involves
income risk due to the variability of prices of feeders, feed and
finished cattle. Several strategies are available to reduce this
risk, including hedging of cattle on feed, participation in a Federal-
Provincial government and producer established income stabilization
program for...
Quick Response is an umbrella term for strategies to cut lead times and to eliminate unnecessary production costs from a manufacturing plant to a consumer market. In particular, the textile and apparel industries need strategies to quickly respond to a changeable market in the international supply chain. As the industry...
Training is a key business process used to increase the skills and knowledge of employees in an effort to improve overall performance. Evaluation of the effectiveness and efficiency of training processes is necessary to ensure time, money, and resources are used to provide the most benefit possible. This investigation is...
Trials to achieve optimal bucking were made with updated OSU-BUCK software in an eastern and a western Oregon location during the summers of 1993 and 1994. The commercial version of the software allows tagging of each log with bar-code identification numbers and therefore provides tracking from stump to customer. Data...
A key application of microchannel process technology (MPT) is its implementation in heat exchanger devices, since a larger surface contact area can be realized than in conventional approaches, thus achieving high heat transfer efficiency. To justify high volume production of configurations validated as prototypes, and to select from among the...
Ocean wave energy is rapidly becoming a field of great interest in the world of renewable energy. Significant advancements in design and technology are being made to make wave energy a viable alternative for our growing energy demands. The two major hurdles for ocean wave energy to make a significant...