The dependence of the substrate resistance, R[subscript sub], for MOS transistor RF modeling on transistor biasing and layout is studied from device simulations and measurements. Though R[subscript sub] is found to be bias dependent, the error incurred by assuming a constant value equal to the DC resistance is not significant....
Estimating the carrier frequency from a modulated waveform is one of the most important functions of a coherent signal receiver. Good performance and low bit error rates are obtained by coherent demodulation. Therefore, exact knowledge of the received signal carrier frequency is critical for communication systems. Also due to the...
Advancements in power electronics to higher power levels and faster switching times allow new machine and systems designs, but also create higher stresses on electric machinery insulation. High performance, pulse-width modulated (PWM) inverters are now available for medium voltage drive systems, and are being considered by the U.S. Navy as...
Phase-locked loop (PLL) frequency synthesizers lie at the heart of most radio transceivers. An important objective of the electronics and communications industry is to design high-speed building blocks which dissipate the lowest possible power, and to ac- complish this with the cheapest technology. The dual-modulus prescaler is one of the...
Advanced low power devices promote the development of micro power generators (MPGs) to replace the batteries to power them. Due to the trend in decreasing integrated circuit (IC) supply voltages, power supply designers are facing more and more serious challenges. The objective of this research is to design a power...
The electrical behavior of on-chip interconnects has become a dominant factor in silicon-based high speed, RF, and mixed-signal integrated circuits. In particular, the frequency-dependent loss mechanisms in heavily-doped silicon substrates can have a large influence on the transmission characteristics of on-chip interconnects. To optimize the performance of the integrated circuit,...
This thesis proposes a novel fully digital technique for the estimation and correction of the DAC error in multi-bit delta sigma ADCs. The structure of the DAC error is indicated through a simple model for unit-element based DACs. The impact of the DAC error on the performance of ADC is...
In this thesis, a novel Direct-Charge-Transfer (DCT) integrator structure is proposed, which can settle much faster than regular switch-capacitor integrators. A new Spread-Spectrum Dynamic Element Matching (SS-DEM) algorithm is also introduced, which can effectively spread or shape the nonlinearity error of multi-bit DAC in the feedback path, thus improve the...
This thesis proposes a novel technique for the design of pipelined and cyclic ADCs utilizing generalized radix gain stages. Several models have been proposed for the optimization of high performance pipelined ADCs by various researchers. This work builds upon them, using a simple but accurate model to estimate the optimal...
This dissertation investigates the use of a hardware mechanism called Eager Data Transfer (EDT) for achieving the reduction of communication latency for user-level network protocol. To reach the goal, the dissertation addresses the following research issues. First, the development of a communication system performance evaluation tool called Linux/SimOS is presented....
Multi-stage delta-sigma (ΔΣ) architectures, commonly known as MASH, are the preferred choice for analog-to-digital converters (ADCs) used in broadband communication applications, where high-resolution (above 14 bits) and high-bandwidth (several MHz) performances are required. Current state-of-the-art designs are capable of as much as 5-MS/s output data rates with 90-dB SNR. However,...
With an increasing number of wireless applications at microwave frequencies, the frequency spectrum is becoming quite crowded. Due to this congestion, the current state of technology is leading towards upper microwave and millimeter wave spectra as they also offer other distinct advantages such as larger bandwidth and smaller component footprint....
In some practical systems, most of the errors are of 1 → 0 type and 0 → 1
errors occur very rarely. In this thesis, first, the capacity of the asymmetric
channel is derived. The capacity of the binary symmetric channel (BSC) and the
Z-channel can be derived from this...
This work focusses on the modeling and the development of efficient coupled simulation techniques for MEMS based RF oscillators. High-level models for MEMS based varactors have been discussed and their accuracy issues are identified, based on comparisons with numerical simulations. A faster simulation approach based on the time-domain shooting method...
Ferrites have been used for various high frequency applications as bulk
materials. These applications, however, are limited to large dimension devices. In
this thesis, thin film ferrites were deposited from a low temperature solution-based
deposition process that is suitable for micro-scale high frequency applications. The
low temperature nature of this...
With the ever-increasing demand for portable devices used in applications
such as wireless communication, mobile computing, consumer electronics, etc.,
the scaling of the CMOS process to deep submicron dimensions becomes more
important to achieve low-cost, low-power and high-performance digital systems.
However, this downscaling also requires similar shrinking of the supply...
Recently, continuous-time ΔΣ modulators are appearing increasingly often in both the literature and the marketplace due to their features of inherent antialiasing and relaxed requirements for opamp and so on. However, several nonideal factors such as clock jitter, excess loop delay, inter-symbol interference and so on, degrade the SNR performance...
There is a large and growing market for portable consumer audio products
with very small size. As the size of these products is reduced, the area occupied
by batteries becomes significant and hence limits the number of batteries to one.
In order to build such small products, high levels of...
Traditionally linear actuator applications are addressed by the use of hydraulic systems. The high maintenance cost and poor reliability will always be the most critical problem in the real applications. Benefited from both the high mechanical advantage of the roll screw and the simple structure of the switched reluctance motor,...
This thesis presents a channelized digital receiver design for UWB sytems in a multipath indoor environment. The UWB technology has been used for commercial and military purposes due to a number of advantages such as low-power consumption, noise-like and carrier free. The energy of UWB signal is spread over a...
The demand for portable electronic systems and the continued
down-scaling of device dimensions resulted in rapid improvement in
the performance of integrated systems. Several low-voltage design
techniques have been proposed to operate analog circuits with sub-1V
supply. However, these techniques require higher power consumption
to achieve large dynamic range while...
Achieving sharpened (enhanced detail) features of a multi-dimensional data source using the linear prediction (LP) bandwidth extrapolation (BWE) technique in the transform domain is the main objective of this research. The evolution of sensor technology has provided acquisition scenarios in which the data format is inherently multi-dimensional, including hyperspectral imaging...
Accurate scaled modeling and simulation are critical to advancing ocean wave linear generator buoys. A 100th scaled model of ocean wave generator buoy systems is analyzed by solving the Navier-Stokes equations. These equations are numerically solved using Computational Fluid Dynamics (CFD) by implementing the front capturing method. In this thesis,...
The amount of instruction level parallelism (ILP) that can be exploited depends
greatly on the size of the instruction window and the number of in-flight instructions
the processor can support. However, this requires a register file with a large set of
physical registers for renaming and multiple ports to provide...
As the functionality of digital chips continues to increase dramatically, chip- to-chip communication bandwidths must scale accordingly to avoid constraining the overall system performance. Therefore, high speed transceiver design has be- come an important research topic. In particular, the performance of the circuits that are responsible for timing accuracy are...
This dissertation presents a dual-path 2-0 MASH (Multi-stAge-noise -SHaping) ADC with two verified digital corrections of DAC mismatch error and quantization noise leakage. By using these two techniques, the requirements for the analog circuits are greatly relaxed. The dual-path structure generates two outputs, one only composed of conversion errors, the...
Delay insensitive asynchronous circuitry provides significant advantages with
respect to substrate noise due to localized switching. The differences between the
substrate noise from NULL Convention Logic (NCL) and traditional Clocked
Boolean Logic (CBL) are described and analyzed based on measured results. A test chip fabricated in the TSMC 0.25 um...
With the growing demand for portable/consumer electronics, such as digital
audio/video (AV), the downscaling of device dimensions, which enables the
integration of an increasing number of transistors in a single chip, is mandatory.
This trend also continuously pushes the power supply voltage down to reduce the
power consumption and improve...
Low-Density Parity-check (LDPC) codes have attracted considerable attention due to their capacity approaching performance over AWGN channel and highly parallelizable decoding schemes. They have been considered in a variety of industry standards for the next generation communication systems. In general, LDPC codes achieve outstanding performance with large codeword lengths (e.g.,...
Nowadays, error correction codes have become an integral part in almost all the modern digital communication and storage systems. With the continuously increasing demands for higher speed and lower power communication systems, efficient VLSI implementations of those error correction codes have great importance for practical applications. In this thesis, several...
Analog-to-Digital Data Converters (ADCs) used in instrumentation and measurements often require high absolute accuracy, including excellent linearity and negligible dc offset. Incremental data converters (IDCs) provide a solution for such measurement applications. Since IDCs are essentially delta-sigma converters with reset operation before each conversion, they retain most of the advantages...
The problem of locating a signal source, or an emitter, has many civilian and military applications, such as communication regulations enforcement, military reconnaissance, and search-and-rescue operations. Many of the most widely used emitter location methods rely on the accurate and robust estimation of the differential time delay,
or time-difference-of-arrival (TDOA),...
Multiple-input multiple-output (MIMO) communication systems have recently been considered as one of the most significant technology breakthroughs for modern wireless communications, due to the higher spectral efficiency and improved link reliability. The sphere decoding algorithm (SDA) has been widely used for maximum likelihood (ML) detection in MIMO systems. It is...
Recently, delta-sigma modulation has become a widely applied technique for high-performance analog-to-digital conversion of narrow-band signals. Most of the early designs used discrete-time structure for good accuracy and good linearity. The transfer functions are independent of the clock frequency. However, high unity-gain bandwidths of the opamps are required to satisfy...
Enabled by continued device scaling in CMOS technology, more and more functions that were previously realized in separate chips are getting integrated on a single chip nowadays. Integration on silicon has opened the door to new portable wireless applications, and initiated a widespread use of these devices in our common...
A two-channel data acquisition system for simultaneous detection and discrimination of beta particles and gamma rays has been developed. Each channel measures and analyzes the input pulses resulting from the absorption of radiation in the layers of the detector. The detector is a triple-layer phoswich (phosphor sandwich) scintillation detector followed...
The Advent of multi-cores allows programs to be executed much faster than before. Cryptoalgorithms use long-bit words thus parallelizing these operations on multi-cores will achieve significant performance improvement. However, not all long-bit word operations in cryptosystems are suitable for parallel execution on multi-cores. In particular, long-bit words used in Elliptic...
The exponential rate of advances in modern communication devices in the last several years have brought us higher levels of functionality and performance as well as reductions in physical size and power consumption. To continue this rate of advancement, next generation systems require wider bandwidth and higher resolution ADCs. Additionally,...
A fully integrated CMOS GPS receiver RF front end optimized for low power operation is presented. The system operates with a supply voltage down to 250 mV. A prototype has been fabricated in a 0.13μm CMOS process and includes a low voltage LNA, quadrature oscillators, and quadrature mixers. It exhibits...
An enhanced swing differential Colpitts VCO (ESDC-VCO) dramatically improves
the swing of a Colpitts VCO by allowing the signal to swing below ground and above the
supply voltage. Fabricated in a 1P8M 0.13 um CMOS process, the ESDC-VCO operates
at 4.9GHz with a 0.475-V supply and consumes 2.7mW. The measured...
An ultra low power crystal oscillator that provides a frequency reference for battery
powered timekeeping applications is presented. An amplitude control circuit is employed to ensure that minimum current is consumed. A subthreshold voltage regulator provides a supply voltage for the oscillator with minimum current consumption. The oscillator and regulator...
Dynamic CMOS circuits are commonly used in high-performance memory arrays to implement wide-NOR logic functions for their read and search operations. This is because dynamic circuits have significantly higher speed and lower area compared to static circuits for performing similar operations. Register File (RF) arrays are located at the top...
Evolution of the mobile communication standards and proliferation of hand-held devices mandate stringent Analog-to-Digital Converter (ADC) specifications. Among various ADCs, a ∆Σ ADC is best known as a power-efficient ADC when more than 12b is required. However, a conventional discrete-time (DT) ∆Σ Modulator (∆ΣM) is inadequate for low-power wideband applications...
With the increasing effort to identify alternative methods of energy generation, extraction of ocean energy has gathered a large interest. Research and industry have begun considering wave energy as the next new alternative energy. The unique challenges of ocean energy requires a wave energy converter to be both robust and...
In Radio Frequency Integrated Circuits (RFIC) or high frequency digital
ICs, there is a demand to probe the internal nodes for testing. The ultra low
capacitance RFIC probe presented in his work is a flexible tool for these
applications. The probe utilizes the coupling between a tungsten needle and the...
A Mobile Ad-hoc NETwork (MANET) is collection of wireless mobile nodes without a network infrastructure or centralized administration. Although MANETs can be used in many applications, such as mobile Internet, military communication, and disaster relief networks, a number of challenges remain. These include routing, medium access control, security, scalability, energy...
This thesis presents two new approaches for the broadband, time-domain modeling of lossy transmission lines. Each approach is based on an alternative derivation of delay extraction in order to separate the line's linear phase from its
attenuation and dispersion. Augmentation networks represent the derived attenuation networks as rational function approximations....
Recent advances in wireless technologies have helped the proliferation of wireless devices, ranging from hand-held devices such as cellular phones to more powerful mobile computing platforms as such laptops [1]. Along with that, the end users’
applications running on these devices, ranging from text message to multimedia applications such as...
In wireless sensor network applications, low-power operation of the wireless receiver is critical. To address this need an ultra-low power Binary Frequency Shift Keying (BFSK) receiver using the super-regenerative architecture is developed.
A prototype receiver is built and tested for operation in the 900 MHz ISM band. Lab measurements show...
Recent developments in computing technology have generated a demand for more streamlined and effective test systems. By replacing traditional in-chassis wired interconnects with a broadcast wireless system, fault detection and error susceptibility will drastically improve, input/output capabilities will expand, and routing complexity will decrease. Ultra-wideband impulse radio's (UWB-IR) characteristic multipath-immunity...
Medical imaging technologies play a vital role in early diagnosis of disease by providing internal images of the human body to medical professionals. Computed Tomography (CT) is currently the most commonly used medical imaging technology because it is easy to use, detectors and scanners are constantly improving, and more importantly,...
Advances in process technologies have led to the development of low-power high speed digital signal processing blocks that occupy small areas. These advances are critical in the development of portable electronic devices with small feature size and long battery life. However, the design of analog and mixed-signal
building blocks, especially...
With the recent interest in increasing the penetration of renewable energy sources onto the power grid, there has been an unprecedented rapid deployment of wind generation, especially in the US Pacific Northwest. While wind farm developers have continued to expand their operations, power system operators are left to deal with...
Ultra-wideband (UWB) radio has become an attractive alternative for wireless communications due to the robustness to multipath fading, low power transmission, mostly-digital implementation, and low cost. Furthermore, short-range, high data-rates applications are possible with UWB radios due to the wide spectral
allocations at 3.1 - 10.6 GHz.
This thesis presents...
The enormous success of wireless technology has recently led to an explosive demand for, and hence a shortage of, bandwidth resources. This expected shortage problem is reported to be primarily due to the inefficient, static nature of current spectrum allocation methods. As an initial step towards solving this shortage problem,...
Short-range wireless communications continually attract interest from both industry and academia, and it is changing our life in every aspect in the last decade. The design of wireless transceivers is the bottleneck for variety applications, due to RF modeling inaccuracy, stringent FCC regulations over the transmitted power spectrum, interference, multi-path...
Given a video, we would like to recognize group activities, localize video parts where these activities occur, and detect actors involved in them. To this and, we propose a novel, mid-level feature, called control point, for representing group activities. The control points are aimed at summarizing visual cues, lifting from...
The decrease of switching times accompanied by the corresponding increase of
clock speeds and data rates, contributes to improve the overall system
computational performance. At the same time, they also affect wireless
communications due to an increment in the emissions of electromagnetic
radiation on the radio bands.
In this dissertation...
Dual referencing has been garnering a lot of attention in the power integrity community, specifically in the voltage mode driver application because it shows a lower overall power delivery noise (PDN) compared to other signal referencing types. Additionally, the increasing push to drive down package and board manufacturing costs is...
As the number of mobile devices accessing large-scale WLANs such as campus
and metropolitan area networks increases, the need for load balancing among the
cells becomes crucial. In addition, the network must also support some minimum
handoff tolerance defined by an application.
A number of load balancing techniques have been...
Two aspects of ADC system performance are addressed in this work. First, the combination of the ADC and its associated reference are co-designed for an energy constrained remote sensing system. Second, sampling linearity is mathematically analyzed as a function of frequency to provide enhanced understanding into an ADC's requisite sampling...
Multi-layer optically coupled scintillation based radiation detectors, known as phoswich detectors, have rapidly evolved in recent years. During the same time, digital signal processing has improved radiation discrimination accuracy and enhanced reliability, while reducing complexity and size of traditional analog signal processing methods. A new generation of high-speed radiation detectors...
High speed serial links are critical components for addressing the growing demand for I/O bandwidth in next-generation computing applications, such as many-core systems, backplane and optical data communications. Due to continued process scaling and circuit innovations, today's CMOS serial link transceivers can achieve tens of Gb/s per pin. However, most...
In networked control systems (NCS) information or packets usually flow from a
sensor or a set of sensors to a remotely located controller. Then the controller
processes the received information and sends a series of control commands to the
actuators through a communication network which could be either wireless or...
The meteoric rise and prevalent usage of wireless networking technologies for mobile
communication applications have captured the attention of media and imagination of
public in the recent decade. One such proliferation is experienced in Wireless Sensor
Networks (WSNs), where multimedia enabled elements are fused with integrated
sensors to empower tightly...
Physical-Layer Network Coding (PNC) is a promising technique that has great potentials for improving the achievable data rates of end-to-end flows through higher packet transmission rates, thereby increasing the overall network throughput. In this thesis, we study the performance of the PNC transmission techniques for unidirectional end-to-end flows in multi-hop...
The stupendous growth in wireless and mobile devices in the recent years has prompted researchers to look at innovative approaches that enable effective use of the available resources. In this thesis, we propose a medium access control (MAC) protocol, referred to as EM-MAC, that enables wireless devices with multi-channel access...
This dissertation presents a low-power high-resolution delta-sigma ADC. Two new architectural design techniques are proposed to reduce the power dissipation of the ADC. Compared to the conventional active adder, the direct charge transfer (DCT) adder greatly saves power by keeping the feedback factor of the active adder unity. However, the...
Complex digital circuits such as microprocessors typically require support circuitry that has traditionally been realized using analog or mixed-signal macros. PLL circuits are used in many integrated applications such as frequency synthesizers and inter-chip communication interfaces. As process technologies advance and grow in complexity, the challenge of maintaining required analog...
Mobile devices are becoming more prevalent and complex. As a result, the wireless communication aspect of these devices is becoming increasingly significant. At the same time, video demands in terms of availability and quality are also on the uprise. High definition (HD) video is the standard of choice for meeting...
The increased use of mobile wireless devices that we have recently been witnessing, such as smartphones, tablets, e-readers, and WiFi enabled devices in general, is driving an unprecedented increase in the amount of data traffic. This fast market adoption of the wireless technology along with the tremendous success of multimedia...
In an industrial and consumer electronic marketplace that is increasingly demanding greater real-world interactivity in portable and distributed devices, analog to digital converter efficiency and performance is being carefully examined. The successive approximation (SAR) analog to digital converter (ADC) architecture has become popular for its high efficiency at mid-speed and...
We develop efficient coordination techniques that support inelastic traffic in large-scale distributed dynamic spectrum access DSA networks. By means of any learning algorithm, the proposed techniques enable DSA users to locate and exploit spectrum opportunities effectively, thereby increasing their achieved throughput (or "rewards" to be more general). Basically, learning algorithms...
Phase Locked Loops(PLLs) are an integral part of almost every electronic system. Systems involving low frequency clocks often require PLLs with low bandwidth. The area occupied by the large loop filter capacitor and resistor in a low bandwidth PLL design makes the realization of traditional charge-pump PLL architecture impractical on...
The proliferation of body worn autometric devices has been enabled by advances in low-power electronics and fueled by the quantified-self movement. These devices range in complexity from pedometers to clinical vital sign measurement. They all share the same drawback, typically the most expensive and heaviest component, the battery. The future...
The Focused Ion Beam (FIB) tool is a versatile instrument for nano-machining in
circuit editing. Circuit editing is one of the most important steps in the design of an
electronic circuit on a chip. Circuit editing can be improved by imaging of silicon
plates and analyzing the resultant images. However...
Traditionally, networking protocol designs have placed much emphasis on point-to-point reliability and efficiency. With the recent rise of mobile and multimedia applications, other considerations such as power consumption and/or Quality of Service (QoS) are becoming increasingly important factors in designing network protocols. As such, we present a new flexible framework...
Frequency synthesizers are critical components of all communication systems. This thesis considers the issue of undesirable frequency spurs of a relatively recent type of frequency synthesis architecture called digital-to-time conversion (DTC). The DTC-based frequency synthesis architecture has important performance benefits over older frequency synthesizers, such as fast frequency switching, large...
High Definition video streaming over WLANs faces many challenges because video data requires not only data integrity but also frames have strict playout deadline. Traditional streaming methods that rely solely on either UDP or TCP have difficulties meeting both requirements because UDP incurs packet loss while TCP incurs delay. This...
Ultra-high-speed (>10GS/s), medium-resolution (5~6bit), low-power (<50mW) analog-to-digital converter can find it application in the areas of digital oscilloscopes and next-generation serial link receivers. There are several challenges to enable a successful design, however. First, the time-interleaved architecture is required in order to achieve over 10GS/s sampling rate, with the trade-off...
For the past half century, CMOS process scaling has followed Moore's law, approximately doubling transistor density every 18 months. While locally routed wires have generally scaled with transistor size, longer wires have scaled at a slower rate and in some cases have grown larger as chip size and complexity have...
Radioxenon detection is a technique used to monitor nuclear explosion and verify the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Because of an ultra-low concentration of radioxenon at radioxenon monitoring stations, radioxenon detection systems must have high sensitivity. This sensitivity is measured in terms of detector's minimum detectable concentration (MDC). It is required...
Routing from a single source node to multiple destination nodes using node disjoint paths (NDP) has many important applications in parallel systems. For example, if a source node wants to send distinct messages to distinct destination nodes, then the one-to-many NDP routing is useful.
Unlike parallel systems with shared-memory, each...
Recent publications show that successive approximation register (SAR) analog to digital converters (ADC) are capable of achieving high efficiency over other ADC topologies. Furthermore, techniques have been adopted to process signals with low activity periods, such as biomedical and industrial sensors. Prior work used least- significant bit first quantization (LSBFQ)...
A procedure for automating the design and layout of analog-to-digital converters (ADCs) is presented. This procedure makes use of the existing synthesis and place-and-route tools that are common in digital circuit design. A method for adding rudimentary analog cells to the standard library is described, allowing the designer to synthesize...
Data converters are essential interface circuits between the analog world that people live in and the digital processors that people live with. Linearity, which often is a tradeoff against other performance criteria, is one of the major performance demands from applications for both analog-to-digital converts (ADC) and digital-to-analog converters (DAC)....
Wireless High Definition Video Transmission (WHDVT) over 802.11-based networks enjoys widespread deployment among today's multimedia solutions. Examples include Intel® Wireless Display and Apple Airplay®, to name a few. In these systems, peer-to-peer networks are established over which H.264-encoded video is transported wirelessly to be decoded and played back at the...
The complexity of designing and testing today's system on chip (SOC) is increasing due to greater integrated circuit (IC) density and higher IO and memory frequencies. SOCs for the mobile phone and tablet market have the unique challenge of short product development windows, at times less than six months, and...
All-digital PLLs promise flexible and precise frequency modulation continous-wave(FMCW) radar signal signal for 77GHz radar applications. Such PLLs require digitally-controlled oscillators(DCO) with wide frequency tuning range and high resolution to address a range of applications and low phase noise requirements. In this thesis, novel resonator structures with ne capacitance/inductance switching...
The ability to accurately locate people and objects indoors will enable opportunities for control and automation of indoor environments. Current indoor localization solutions require dedicated hardware which must be custom tailored to each application. There are large technological, societal, and economic benefits in developing a more general purpose system that...
The design of mobile wireless devices has always focused on reducing power, area, and cost. This dissertation proposes two techniques that are leveraged to save power and area and therefore cost. The first techniques reduces the noise in the receiver and results in a relaxed power requirement. The second technique...
Detection of xenon radioisotopes (radioxenons) has proven to be an important method for detecting nuclear explosions and is particularly well suited for detecting undeclared underground testing. The radioxenon isotopes ¹³¹mXe (t₁/₂ = 11.934 d), ¹³³mXe (t₁/₂ = 2.19 d), ¹³³Xe (t₁/₂ = 5.243 d) and ¹³⁵Xe (t₁/₂ = 9.14 h)...
In wireless communication, channel state information (CSI) is essential for data detection. Fast fading coefficients estimation is important in order to acquire accurate CSI. Kalman filters (KF) are widely used for real time parameter estimation and can be used to estimate the fast fading coefficients of a mobile communication channel....
Massive MIMO is a promising technique for future 5G communications due to its high spectrum and energy efficiency. To realize its potential performance gain, accurate channel state information at transmitter side (CSIT) is essential. Frequency division duplex (FDD) is widely employed by the most cellular systems today. However, it requires...
This dissertation focuses on the development of ultra-compact optical devices for free-space modulation. We propose a surface-normal modulator using metallic photonic crystals for free-space optical interconnects. The active control of light intensity is achieved by engineering the Fano resonances in metallic photonic crystals. Both thermo-optic modulation and electro-optic modulation of...
Recent sensor System-on-Chips (SoC) have enabled significant advances in energy-efficiency by incorporating various micro-powered building blocks. Unfortunately, most of these sensor systems do not address the high power cost associated with data storage and transmission, which in some cases vastly exceeds the power consumed by the rest of the SoC....
Triangulateration uses geometric distance to estimate the location of user by employing techniques like received signal strength (RSS), time-of-arrival (TOA), time-difference-of-arrival (TDOA) and image processing.
Radio frequency (RF) signal positioning using TOA or TDOA techniques generally requires timing synchronization of the anchors and/or the anchors and targets. If the desired...
The Comprehensive Nuclear-Test-Ban Treaty (CTBT) bans all nuclear explosion tests for military or civilian purposes. The International Monitoring System (IMS) was established to verify compliance with the treaty. It consists of several monitoring stations that detect: seismic activities, hydrocoustic activities, infrasound waves, and radionuclide particles and noble gases. Radioxenon detection...
Analog-to-digital converters are essential components to the portable devices that we are using today. Wireless sensors, body implanted devices, communication devices and so forth require low power ADCs. Therefore achieving higher resolution and bandwidth with lower power consumption is targeted in ADCs design. In this work power efficient ADCs for...
Filters and data converters are key analog-and-mixed-signal (AMS) building blocks in communication systems, such as software-defined radios and internet-of-things. In this dissertation, novel switched-capacitor filter and analog-to-digital converter (ADC) circuit configurations have been explored which are power efficient and are digital scaling friendly.
First, a novel switched-capacitor low-pass filter architecture...